Atmel Software Framework

avr2025_mac/source/tal/at86rf231/inc/at86rf231.h File Reference
#include "tal_types.h"

Macros

#define AACK_ACK_TIME_12_SYMBOLS   (0)
 Constants. More...
 
#define AACK_ACK_TIME_2_SYMBOLS   (1)
 Constant AACK_ACK_TIME_2_symbols for sub-register SR_AACK_ACK_TIME. More...
 
#define ACK_DISABLE   (1)
 Constant ACK_DISABLE for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1. More...
 
#define ACK_ENABLE   (0)
 Constant ACK_ENABLE for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1. More...
 
#define AES_BASE_ADDR   (0x80)
 Register addresses. More...
 
#define AES_DIR_DECRYPT   (1)
 AES core operation direction: Decryption (ECB) More...
 
#define AES_DIR_ENCRYPT   (0)
 AES core operation direction: Encryption (ECB, CBC) More...
 
#define AES_DONE   (1)
 AES core operation status: AES module finished. More...
 
#define AES_MODE_CBC   (2)
 Set CBC mode. More...
 
#define AES_MODE_ECB   (0)
 Set ECB mode. More...
 
#define AES_MODE_KEY   (1)
 Set key mode. More...
 
#define AES_NOT_DONE   (0)
 AES core operation status: AES module did not finish. More...
 
#define AES_REQUEST   (1)
 Initiate an AES operation. More...
 
#define ALTRATE_1MBPS   (2)
 Constant ALTRATE_1Mbps for sub-register SR_OQPSK_DATA_RATE. More...
 
#define ALTRATE_250KBPS   (0)
 Constant ALTRATE_250kbps for sub-register SR_OQPSK_DATA_RATE. More...
 
#define ALTRATE_2MBPS   (3)
 Constant ALTRATE_2Mbps for sub-register SR_OQPSK_DATA_RATE. More...
 
#define ALTRATE_500KBPS   (1)
 Constant ALTRATE_500kbps for sub-register SR_OQPSK_DATA_RATE. More...
 
#define ANT_CTRL_0   (0)
 Constant ANT_CTRL_0 for sub-register SR_ANT_CTRL in register RG_ANT_DIV. More...
 
#define ANT_CTRL_1   (1)
 Constant ANT_CTRL_1 for sub-register SR_ANT_CTRL in register RG_ANT_DIV. More...
 
#define ANT_CTRL_2   (2)
 Constant ANT_CTRL_2 for sub-register SR_ANT_CTRL in register RG_ANT_DIV. More...
 
#define ANT_CTRL_3   (3)
 Constant ANT_CTRL_3 for sub-register SR_ANT_CTRL in register RG_ANT_DIV. More...
 
#define ANT_DIV_DISABLE   (0)
 Constant ANT_DIV_disable for sub-register SR_ANT_DIV_EN. More...
 
#define ANT_DIV_ENABLE   (1)
 Constant ANT_DIV_enable for sub-register SR_ANT_DIV_EN. More...
 
#define ANT_EXT_SW_DISABLE   (0)
 Constant ANT_EXT_SW_DISABLE for sub-register SR_ANT_EXT_SW_EN. More...
 
#define ANT_EXT_SW_ENABLE   (1)
 Constant ANT_EXT_SW_ENABLE for sub-register SR_ANT_EXT_SW_EN. More...
 
#define ANT_SEL_ANTENNA_0   (0)
 Constant ANT_SEL_antenna_0 for sub-register SR_ANT_SEL. More...
 
#define ANT_SEL_ANTENNA_1   (1)
 Constant ANT_SEL_antenna_1 for sub-register SR_ANT_SEL. More...
 
#define AT86RF231_PART_NUM   (3)
 Constant RF231 for sub-register SR_PART_NUM. More...
 
#define AT86RF231_VERSION_NUM   (2)
 Constant RF231 for sub-register SR_VERSION_NUM. More...
 
#define BATMON_ABOVE_THRES   (1)
 Constant BATMON_ABOVE_THRES for sub-register SR_BATMON_OK. More...
 
#define BATMON_BELOW_THRES   (0)
 Constant BATMON_BELOW_THRES for sub-register SR_BATMON_OK. More...
 
#define BATMON_HIGH_RANGE   (1)
 Constant BATMON_HIGH_RANGE for sub-register BATMON_HR in register RG_BATMON. More...
 
#define BATMON_LOW_RANGE   (0)
 Constant BATMON_LOW_RANGE for sub-register BATMON_HR in register RG_BATMON. More...
 
#define CCA_DETECTION_DONE   (1)
 Constant CCA_calculation_done for sub-register SR_CCA_DONE. More...
 
#define CCA_DETECTION_NOT_DONE   (0)
 Constant CCA_calculation_not_finished for sub-register SR_CCA_DONE. More...
 
#define CCA_DETECTION_TIME_SYM   (8)
 
#define CCA_DURATION_SYM
 
#define CCA_MODE_0   (0)
 Constant CCA_Mode_0 for sub-register SR_CCA_MODE. More...
 
#define CCA_MODE_1   (1)
 Constant CCA_Mode_1 for sub-register SR_CCA_MODE. More...
 
#define CCA_MODE_2   (2)
 Constant CCA_Mode_2 for sub-register SR_CCA_MODE. More...
 
#define CCA_MODE_3   (3)
 Constant CCA_Mode_3 for sub-register SR_CCA_MODE. More...
 
#define CCA_PRE_START_DURATION_US   (20)
 
#define CCA_PREPARATION_DURATION_US   (50)
 
#define CCA_PROCESS_TIME_SYM   (1)
 
#define CCA_START   (1)
 Constant CCA_START for sub-register CCA_REQUEST in register RG_PHY_CC_CCA. More...
 
#define CCA_STATUS_CHANNEL_IS_BUSY   (0)
 Constant CCA_STATUS_channel_is_busy for sub-register SR_CCA_STATUS. More...
 
#define CCA_STATUS_CHANNEL_IS_IDLE   (1)
 Constant CCA_STATUS_channel_is_idle for sub-register SR_CCA_STATUS. More...
 
#define CLKM_16MHZ   (5)
 Constant CLKM_16MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_1_16MHZ   (7)
 Constant CLKM_1_16MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_1_4MHZ   (6)
 Constant CLKM_1_4MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_1MHZ   (1)
 Constant CLKM_1MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_2MHZ   (2)
 Constant CLKM_2MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_4MHZ   (3)
 Constant CLKM_4MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_8MHZ   (4)
 Constant CLKM_8MHz for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_NO_CLOCK   (0)
 Constant CLKM_no_clock for sub-register SR_CLKM_CTRL. More...
 
#define CLKM_SHA_DISABLE   (0)
 Constant CLKM_SHA_disable for sub-register SR_CLKM_SHA_SEL. More...
 
#define CLKM_SHA_ENABLE   (1)
 Constant CLKM_SHA_enable for sub-register SR_CLKM_SHA_SEL. More...
 
#define CRC16_NOT_VALID   (0)
 Constant CRC16_not_valid for sub-register SR_RX_CRC_VALID. More...
 
#define CRC16_VALID   (1)
 Constant CRC16_valid for sub-register SR_RX_CRC_VALID. More...
 
#define CSMA_PROCESSING_TIME_US   (100)
 
#define FRAME_VERSION_0   (0)
 Constant FRAME_VERSION_0 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1. More...
 
#define FRAME_VERSION_01   (1)
 Constant FRAME_VERSION_01 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1. More...
 
#define FRAME_VERSION_012   (2)
 Constant FRAME_VERSION_012 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1. More...
 
#define FRAME_VERSION_IGNORED   (3)
 Constant FRAME_VERSION_IGNORED for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1. More...
 
#define IRQ_MASK_MODE_OFF   (0)
 Constant IRQ_MASK_MODE_off for sub-register SR_IRQ_MASK_MODE. More...
 
#define IRQ_MASK_MODE_ON   (1)
 Constant IRQ_MASK_MODE_on for sub-register SR_IRQ_MASK_MODE. More...
 
#define IRQ_POL_HIGH_ACTIVE_IRQ   (0)
 Constant IRQ_POL_high_active_IRQ for sub-register SR_IRQ_POLARITY. More...
 
#define IRQ_POL_LOW_ACTIVE_IRQ   (1)
 Constant IRQ_POL_low_active_IRQ for sub-register SR_IRQ_POLARITY. More...
 
#define IRQ_PROCESSING_DLY_US   (32)
 
#define OQPSK_SCRAM_DISABLE   (0)
 Constant OQPSK_SCRAM_DISABLE for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2. More...
 
#define OQPSK_SCRAM_ENABLE   (1)
 Constant OQPSK_SCRAM_ENABLE for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2. More...
 
#define P_ON_TO_CLKM_AVAILABLE_MAX_US
 
#define P_ON_TO_CLKM_AVAILABLE_TYP_US
 
#define PA_BUF_LT_0_US   (0)
 Constant PA_BUF_LT_0s for sub-register SR_PA_BUF_LT. More...
 
#define PA_BUF_LT_2_US   (1)
 Constant PA_BUF_LT_2s for sub-register SR_PA_BUF_LT. More...
 
#define PA_BUF_LT_4_US   (2)
 Constant PA_BUF_LT_4s for sub-register SR_PA_BUF_LT. More...
 
#define PA_BUF_LT_6_US   (3)
 Constant PA_BUF_LT_6s for sub-register SR_PA_BUF_LT. More...
 
#define PA_EXT_DISABLE   (0)
 Constant PA_EXT_disable for sub-register SR_PA_EXT_EN. More...
 
#define PA_EXT_ENABLE   (1)
 Constant PA_EXT_enable for sub-register SR_PA_EXT_EN. More...
 
#define PA_LT_2_US   (0)
 Constant PA_LT_2s for sub-register SR_PA_LT. More...
 
#define PA_LT_4_US   (1)
 Constant PA_LT_4s for sub-register SR_PA_LT. More...
 
#define PA_LT_6_US   (2)
 Constant PA_LT_6s for sub-register SR_PA_LT. More...
 
#define PA_LT_8_US   (3)
 Constant PA_LT_8s for sub-register SR_PA_LT. More...
 
#define PAD_CLKM_2_MA   (0)
 Constant PAD_CLKM_2mA for sub-register SR_PAD_IO_CLKM. More...
 
#define PAD_CLKM_4_MA   (1)
 Constant PAD_CLKM_4mA for sub-register SR_PAD_IO_CLKM. More...
 
#define PAD_CLKM_6_MA   (2)
 Constant PAD_CLKM_6mA for sub-register SR_PAD_IO_CLKM. More...
 
#define PAD_CLKM_8_MA   (3)
 Constant PAD_CLKM_8mA for sub-register SR_PAD_IO_CLKM. More...
 
#define PAD_IO_2_MA   (0)
 Constant PAD_IO_2mA for sub-register SR_PAD_IO. More...
 
#define PAD_IO_4_MA   (1)
 Constant PAD_IO_4mA for sub-register SR_PAD_IO. More...
 
#define PAD_IO_6_MA   (2)
 Constant PAD_IO_6mA for sub-register SR_PAD_IO. More...
 
#define PAD_IO_8_MA   (3)
 Constant PAD_IO_8mA for sub-register SR_PAD_IO. More...
 
#define PD_ACK_BIT_SET_DISABLE   (0)
 Constant PD_ACK_BIT_SET_DISABLE for sub-register AACK_SET_PD in register RG_CSMA_SEED_1. More...
 
#define PD_ACK_BIT_SET_ENABLE   (1)
 Constant PD_ACK_BIT_SET_ENABLE for sub-register AACK_SET_PD in register RG_CSMA_SEED_1. More...
 
#define PRE_TX_DURATION_US   (32)
 
#define PROM_MODE_DISABLE   (0)
 Constant PROM_MODE_DISABLE for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1. More...
 
#define PROM_MODE_ENABLE   (1)
 Constant PROM_MODE_ENABLE for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1. More...
 
#define RF231_RAM_SIZE   (0x80)
 RF231 FIFO size. More...
 
#define RG_AES_CTRL   (0x03)
 Offset for register AES_CTRL. More...
 
#define RG_AES_CTRL_MIRROR   (0x94)
 mirrored version of AES_CTRL, SRAM address More...
 
#define RG_AES_STATE_KEY_0   (0x04)
 Offset for register AES_STATE_KEY_0. More...
 
#define RG_AES_STATUS   (0x02)
 Offset for register AES_STATUS. More...
 
#define RG_ANT_DIV   (0x0d)
 Offset for register ANT_DIV. More...
 
#define RG_BATMON   (0x11)
 Offset for register BATMON. More...
 
#define RG_CCA_THRES   (0x09)
 Offset for register CCA_THRES. More...
 
#define RG_CSMA_BE   (0x2f)
 Offset for register CSMA_BE. More...
 
#define RG_CSMA_SEED_0   (0x2d)
 Offset for register CSMA_SEED_0. More...
 
#define RG_CSMA_SEED_1   (0x2e)
 Offset for register CSMA_SEED_1. More...
 
#define RG_FTN_CTRL   (0x18)
 Offset for register FTN_CTRL. More...
 
#define RG_IEEE_ADDR_0   (0x24)
 Offset for register IEEE_ADDR_0. More...
 
#define RG_IEEE_ADDR_1   (0x25)
 Offset for register IEEE_ADDR_1. More...
 
#define RG_IEEE_ADDR_2   (0x26)
 Offset for register IEEE_ADDR_2. More...
 
#define RG_IEEE_ADDR_3   (0x27)
 Offset for register IEEE_ADDR_3. More...
 
#define RG_IEEE_ADDR_4   (0x28)
 Offset for register IEEE_ADDR_4. More...
 
#define RG_IEEE_ADDR_5   (0x29)
 Offset for register IEEE_ADDR_5. More...
 
#define RG_IEEE_ADDR_6   (0x2a)
 Offset for register IEEE_ADDR_6. More...
 
#define RG_IEEE_ADDR_7   (0x2b)
 Offset for register IEEE_ADDR_7. More...
 
#define RG_IRQ_MASK   (0x0e)
 Offset for register IRQ_MASK. More...
 
#define RG_IRQ_STATUS   (0x0f)
 Offset for register IRQ_STATUS. More...
 
#define RG_MAN_ID_0   (0x1e)
 Offset for register MAN_ID_0. More...
 
#define RG_MAN_ID_1   (0x1f)
 Offset for register MAN_ID_1. More...
 
#define RG_PAN_ID_0   (0x22)
 Offset for register PAN_ID_0. More...
 
#define RG_PAN_ID_1   (0x23)
 Offset for register PAN_ID_1. More...
 
#define RG_PART_NUM   (0x1c)
 Offset for register PART_NUM. More...
 
#define RG_PHY_CC_CCA   (0x08)
 Offset for register PHY_CC_CCA. More...
 
#define RG_PHY_ED_LEVEL   (0x07)
 Offset for register PHY_ED_LEVEL. More...
 
#define RG_PHY_RSSI   (0x06)
 Offset for register PHY_RSSI. More...
 
#define RG_PHY_TX_PWR   (0x05)
 Offset for register PHY_TX_PWR. More...
 
#define RG_PLL_CF   (0x1a)
 Offset for register PLL_CF. More...
 
#define RG_PLL_DCU   (0x1b)
 Offset for register PLL_DCU. More...
 
#define RG_RX_CTRL   (0x0a)
 Offset for register RX_CTRL. More...
 
#define RG_RX_SYN   (0x15)
 Offset for register RX_SYN. More...
 
#define RG_SFD_VALUE   (0x0b)
 Offset for register SFD_VALUE. More...
 
#define RG_SHORT_ADDR_0   (0x20)
 Offset for register SHORT_ADDR_0. More...
 
#define RG_SHORT_ADDR_1   (0x21)
 Offset for register SHORT_ADDR_1. More...
 
#define RG_TRX_CTRL_0   (0x03)
 Offset for register TRX_CTRL_0. More...
 
#define RG_TRX_CTRL_1   (0x04)
 Offset for register TRX_CTRL_1. More...
 
#define RG_TRX_CTRL_2   (0x0c)
 Offset for register TRX_CTRL_2. More...
 
#define RG_TRX_STATE   (0x02)
 Offset for register TRX_STATE. More...
 
#define RG_TRX_STATUS   (0x01)
 Offset for register TRX_STATUS. More...
 
#define RG_VERSION_NUM   (0x1d)
 Offset for register VERSION_NUM. More...
 
#define RG_VREG_CTRL   (0x10)
 Offset for register VREG_CTRL. More...
 
#define RG_XAH_CTRL_0   (0x2c)
 Offset for register XAH_CTRL_0. More...
 
#define RG_XAH_CTRL_1   (0x17)
 Offset for register XAH_CTRL_1. More...
 
#define RG_XOSC_CTRL   (0x12)
 Offset for register XOSC_CTRL. More...
 
#define RSSI_BASE_VAL_DBM   (-91)
 Minimum RSSI sensitivity value in dBm, which is equivalent to the value 0 in sub register SR_RSSI. More...
 
#define RST_PULSE_WIDTH_US   (10)
 
#define RX_DISABLE   (1)
 Constant RX_DISABLE for sub-register RX_PDT_DIS. More...
 
#define RX_ENABLE   (0)
 Constant RX_ENABLE for sub-register RX_PDT_DIS. More...
 
#define RX_SAFE_MODE_DISABLE   (0)
 Constant RX_SAFE_MODE_DISABLE for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2. More...
 
#define RX_SAFE_MODE_ENABLE   (1)
 Constant RX_SAFE_MODE_ENABLE for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2. More...
 
#define SLEEP_TO_TRX_OFF_MAX_US
 
#define SLEEP_TO_TRX_OFF_TYP_US
 
#define SPI_CMD_MODE_DEFAULT   (0)
 Constant SPI_CMD_MODE_default for sub-register SR_SPI_CMD_MODE. More...
 
#define SPI_CMD_MODE_MONITOR_IRQ_STATUS   (3)
 Constant SPI_CMD_MODE_monitor_IRQ_STATUS for sub-register SR_SPI_CMD_MODE. More...
 
#define SPI_CMD_MODE_MONITOR_PHY_RSSI   (2)
 Constant SPI_CMD_MODE_monitor_PHY_RSSI for sub-register SR_SPI_CMD_MODE. More...
 
#define SPI_CMD_MODE_MONITOR_TRX_STATUS   (1)
 Constant SPI_CMD_MODE_monitor_TRX_STATUS for sub-register SR_SPI_CMD_MODE. More...
 
#define SR_AACK_ACK_TIME   0x17, 0x04, 2
 Subregister access. More...
 
#define SR_AACK_DIS_ACK   0x2e, 0x10, 4
 Access parameters for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1. More...
 
#define SR_AACK_FLTR_RES_FT   0x17, 0x20, 5
 Access parameters for sub-register AACK_FLTR_RES_FT in register RG_XAH_CTRL_1. More...
 
#define SR_AACK_FVN_MODE   0x2e, 0xc0, 6
 Access parameters for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1. More...
 
#define SR_AACK_I_AM_COORD   0x2e, 0x08, 3
 Access parameters for sub-register AACK_I_AM_COORD in register RG_CSMA_SEED_1. More...
 
#define SR_AACK_PROM_MODE   0x17, 0x02, 1
 Access parameters for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1. More...
 
#define SR_AACK_SET_PD   0x2e, 0x20, 5
 Access parameters for sub-register AACK_SET_PD in register RG_CSMA_SEED_1. More...
 
#define SR_AACK_UPLD_RES_FT   0x17, 0x10, 4
 Access parameters for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1. More...
 
#define SR_AES_DIR   0x03, 0x08, 3
 Access parameters for sub-register AES_DIR in register RG_AES_CTRL. More...
 
#define SR_AES_MODE   0x03, 0x70, 4
 Access parameters for sub-register AES_MODE in register RG_AES_CTRL. More...
 
#define SR_AES_REQUEST   0x03, 0x80, 7
 Access parameters for sub-register AES_REQUEST in register RG_AES_CTRL. More...
 
#define SR_ANT_CTRL   0x0d, 0x03, 0
 Access parameters for sub-register ANT_CTRL in register RG_ANT_DIV. More...
 
#define SR_ANT_DIV_EN   0x0d, 0x08, 3
 Access parameters for sub-register ANT_DIV_EN in register RG_ANT_DIV. More...
 
#define SR_ANT_EXT_SW_EN   0x0d, 0x04, 2
 Access parameters for sub-register ANT_EXT_SW_EN in register RG_ANT_DIV. More...
 
#define SR_ANT_SEL   0x0d, 0x80, 7
 Access parameters for sub-register ANT_SEL in register RG_ANT_DIV. More...
 
#define SR_AVDD_OK   0x10, 0x40, 6
 Access parameters for sub-register AVDD_OK in register RG_VREG_CTRL. More...
 
#define SR_AVREG_EXT   0x10, 0x80, 7
 Access parameters for sub-register AVREG_EXT in register RG_VREG_CTRL. More...
 
#define SR_BATMON_HR   0x11, 0x10, 4
 Access parameters for sub-register BATMON_HR in register RG_BATMON. More...
 
#define SR_BATMON_OK   0x11, 0x20, 5
 Access parameters for sub-register BATMON_OK in register RG_BATMON. More...
 
#define SR_BATMON_VTH   0x11, 0x0f, 0
 Access parameters for sub-register BATMON_VTH in register RG_BATMON. More...
 
#define SR_CCA_DONE   0x01, 0x80, 7
 Access parameters for sub-register CCA_DONE in register RG_TRX_STATUS. More...
 
#define SR_CCA_ED_THRES   0x09, 0x0f, 0
 Access parameters for sub-register CCA_ED_THRES in register RG_CCA_THRES. More...
 
#define SR_CCA_MODE   0x08, 0x60, 5
 Access parameters for sub-register CCA_MODE in register RG_PHY_CC_CCA. More...
 
#define SR_CCA_REQUEST   0x08, 0x80, 7
 Access parameters for sub-register CCA_REQUEST in register RG_PHY_CC_CCA. More...
 
#define SR_CCA_STATUS   0x01, 0x40, 6
 Access parameters for sub-register CCA_STATUS in register RG_TRX_STATUS. More...
 
#define SR_CHANNEL   0x08, 0x1f, 0
 Access parameters for sub-register CHANNEL in register RG_PHY_CC_CCA. More...
 
#define SR_CLKM_CTRL   0x03, 0x07, 0
 Access parameters for sub-register CLKM_CTRL in register RG_TRX_CTRL_0. More...
 
#define SR_CLKM_SHA_SEL   0x03, 0x08, 3
 Access parameters for sub-register CLKM_SHA_SEL in register RG_TRX_CTRL_0. More...
 
#define SR_CSMA_SEED_0   0x2d, 0xff, 0
 Access parameters for sub-register CSMA_SEED_0 in register RG_CSMA_SEED_0. More...
 
#define SR_CSMA_SEED_1   0x2e, 0x07, 0
 Access parameters for sub-register CSMA_SEED_1 in register RG_CSMA_SEED_1. More...
 
#define SR_DVDD_OK   0x10, 0x04, 2
 Access parameters for sub-register DVDD_OK in register RG_VREG_CTRL. More...
 
#define SR_DVREG_EXT   0x10, 0x08, 3
 Access parameters for sub-register DVREG_EXT in register RG_VREG_CTRL. More...
 
#define SR_ED_LEVEL   0x07, 0xff, 0
 Access parameters for sub-register ED_LEVEL in register RG_PHY_ED_LEVEL. More...
 
#define SR_FTN_START   0x18, 0x80, 7
 Access parameters for sub-register FTN_START in register RG_FTN_CTRL. More...
 
#define SR_IEEE_ADDR_0   0x24, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_0 in register RG_IEEE_ADDR_0. More...
 
#define SR_IEEE_ADDR_1   0x25, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_1 in register RG_IEEE_ADDR_1. More...
 
#define SR_IEEE_ADDR_2   0x26, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_2 in register RG_IEEE_ADDR_2. More...
 
#define SR_IEEE_ADDR_3   0x27, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_3 in register RG_IEEE_ADDR_3. More...
 
#define SR_IEEE_ADDR_4   0x28, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_4 in register RG_IEEE_ADDR_4. More...
 
#define SR_IEEE_ADDR_5   0x29, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_5 in register RG_IEEE_ADDR_5. More...
 
#define SR_IEEE_ADDR_6   0x2a, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_6 in register RG_IEEE_ADDR_6. More...
 
#define SR_IEEE_ADDR_7   0x2b, 0xff, 0
 Access parameters for sub-register IEEE_ADDR_7 in register RG_IEEE_ADDR_7. More...
 
#define SR_IRQ_0_PLL_LOCK   0x0f, 0x01, 0
 Access parameters for sub-register IRQ_0_PLL_LOCK in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_1_PLL_UNLOCK   0x0f, 0x02, 1
 Access parameters for sub-register IRQ_1_PLL_UNLOCK in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_2_EXT_EN   0x04, 0x40, 6
 Access parameters for sub-register IRQ_2_EXT_EN in register RG_TRX_CTRL_1. More...
 
#define SR_IRQ_2_RX_START   0x0f, 0x04, 2
 Access parameters for sub-register IRQ_2_RX_START in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_3_TRX_END   0x0f, 0x08, 3
 Access parameters for sub-register IRQ_3_TRX_END in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_4_CCA_ED_READY   0x0f, 0x10, 4
 Access parameters for sub-register IRQ_4_CCA_ED_READY in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_5_AMI   0x0f, 0x20, 5
 Access parameters for sub-register IRQ_5_AMI in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_6_TRX_UR   0x0f, 0x40, 6
 Access parameters for sub-register IRQ_6_TRX_UR in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_7_BAT_LOW   0x0f, 0x80, 7
 Access parameters for sub-register IRQ_7_BAT_LOW in register RG_IRQ_STATUS. More...
 
#define SR_IRQ_MASK   0x0e, 0xff, 0
 Access parameters for sub-register IRQ_MASK in register RG_IRQ_MASK. More...
 
#define SR_IRQ_MASK_MODE   0x04, 0x02, 1
 Access parameters for sub-register IRQ_MASK_MODE in register RG_TRX_CTRL_1. More...
 
#define SR_IRQ_POLARITY   0x04, 0x01, 0
 Access parameters for sub-register IRQ_POLARITY in register RG_TRX_CTRL_1. More...
 
#define SR_MAN_ID_0   0x1e, 0xff, 0
 Access parameters for sub-register MAN_ID_0 in register RG_MAN_ID_0. More...
 
#define SR_MAN_ID_1   0x1f, 0xff, 0
 Access parameters for sub-register MAN_ID_1 in register RG_MAN_ID_1. More...
 
#define SR_MAX_BE   0x2f, 0xf0, 4
 Access parameters for sub-register MAX_BE in register RG_CSMA_BE. More...
 
#define SR_MAX_CSMA_RETRIES   0x2c, 0x0e, 1
 Access parameters for sub-register MAX_CSMA_RETRIES in register RG_XAH_CTRL_0. More...
 
#define SR_MAX_FRAME_RETRIES   0x2c, 0xf0, 4
 Access parameters for sub-register MAX_FRAME_RETRIES in register RG_XAH_CTRL_0. More...
 
#define SR_MIN_BE   0x2f, 0x0f, 0
 Access parameters for sub-register MIN_BE in register RG_CSMA_BE. More...
 
#define SR_OQPSK_DATA_RATE   0x0c, 0x03, 0
 Access parameters for sub-register OQPSK_DATA_RATE in register RG_TRX_CTRL_2. More...
 
#define SR_OQPSK_SCRAM_EN   0x0C, 0x20, 5
 Access parameters for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2. More...
 
#define SR_PA_BUF_LT   0x05, 0xc0, 6
 Access parameters for sub-register PA_BUF_LT in register RG_PHY_TX_PWR. More...
 
#define SR_PA_EXT_EN   0x04, 0x80, 7
 Access parameters for sub-register PA_EXT_EN in register RG_TRX_CTRL_1. More...
 
#define SR_PA_LT   0x05, 0x30, 4
 Access parameters for sub-register PA_LT in register RG_PHY_TX_PWR. More...
 
#define SR_PAD_IO   0x03, 0xc0, 6
 Access parameters for sub-register PAD_IO in register RG_TRX_CTRL_0. More...
 
#define SR_PAD_IO_CLKM   0x03, 0x30, 4
 Access parameters for sub-register PAD_IO_CLKM in register RG_TRX_CTRL_0. More...
 
#define SR_PAN_ID_0   0x22, 0xff, 0
 Access parameters for sub-register PAN_ID_0 in register RG_PAN_ID_0. More...
 
#define SR_PAN_ID_1   0x23, 0xff, 0
 Access parameters for sub-register PAN_ID_1 in register RG_PAN_ID_1. More...
 
#define SR_PART_NUM   0x1c, 0xff, 0
 Access parameters for sub-register PART_NUM in register RG_PART_NUM. More...
 
#define SR_PDT_THRES   0x0a, 0x0f, 0
 Access parameters for sub-register PDT_THRES in register RG_RX_CTRL. More...
 
#define SR_PLL_CF_START   0x1a, 0x80, 7
 Access parameters for sub-register PLL_CF_START in register RG_PLL_CF. More...
 
#define SR_PLL_DCU_START   0x1b, 0x80, 7
 Access parameters for sub-register PLL_DCU_START in register RG_PLL_DCU. More...
 
#define SR_RND_VALUE   0x06, 0x60, 5
 Access parameters for sub-register RND_VALUE in register RG_PHY_RSSI. More...
 
#define SR_RSSI   0x06, 0x1f, 0
 Access parameters for sub-register RSSI in register RG_PHY_RSSI. More...
 
#define SR_RX_BL_CTRL   0x04, 0x10, 4
 Access parameters for sub-register RX_BL_CTRL in register RG_TRX_CTRL_1. More...
 
#define SR_RX_CRC_VALID   0x06, 0x80, 7
 Access parameters for sub-register RX_CRC_VALID in register RG_PHY_RSSI. More...
 
#define SR_RX_PDT_DIS   0x15, 0x80, 7
 Access parameters for sub-register RX_PDT_DIS in register RG_RX_SYN. More...
 
#define SR_RX_PDT_LEVEL   0x15, 0x0f, 0
 Access parameters for sub-register RX_PDT_LEVEL in register RG_RX_SYN. More...
 
#define SR_RX_SAFE_MODE   0x0c, 0x80, 7
 Access parameters for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2. More...
 
#define SR_SFD_VALUE   0x0b, 0xff, 0
 Access parameters for sub-register SFD_VALUE in register RG_SFD_VALUE. More...
 
#define SR_SHORT_ADDR_0   0x20, 0xff, 0
 Access parameters for sub-register SHORT_ADDR_0 in register RG_SHORT_ADDR_0. More...
 
#define SR_SHORT_ADDR_1   0x21, 0xff, 0
 Access parameters for sub-register SHORT_ADDR_1 in register RG_SHORT_ADDR_1. More...
 
#define SR_SLOTTED_OPERATION   0x2c, 0x01, 0
 Access parameters for sub-register SLOTTED_OPERATION in register RG_XAH_CTRL_0. More...
 
#define SR_SPI_CMD_MODE   0x04, 0x0c, 2
 Access parameters for sub-register SPI_CMD_MODE in register RG_TRX_CTRL_1. More...
 
#define SR_TRAC_STATUS   0x02, 0xe0, 5
 Access parameters for sub-register TRAC_STATUS in register RG_TRX_STATE. More...
 
#define SR_TRX_CMD   0x02, 0x1f, 0
 Access parameters for sub-register TRX_CMD in register RG_TRX_STATE. More...
 
#define SR_TRX_STATUS   0x01, 0x1f, 0
 Access parameters for sub-register TRX_STATUS in register RG_TRX_STATUS. More...
 
#define SR_TX_AUTO_CRC_ON   0x04, 0x20, 5
 Access parameters for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1. More...
 
#define SR_TX_PWR   0x05, 0x0f, 0
 Access parameters for sub-register TX_PWR in register RG_PHY_TX_PWR. More...
 
#define SR_VERSION_NUM   0x1d, 0xff, 0
 Access parameters for sub-register VERSION_NUM in register RG_VERSION_NUM. More...
 
#define SR_XTAL_MODE   0x12, 0xf0, 4
 Access parameters for sub-register XTAL_MODE in register RG_XOSC_CTRL. More...
 
#define SR_XTAL_TRIM   0x12, 0x0f, 0
 Access parameters for sub-register XTAL_TRIM in register RG_XOSC_CTRL. More...
 
#define T_OCT   32
 Duration of an octet for 250kb/s OQPSK mode in us. More...
 
#define T_SYM   16
 Duration of an symbol for 250kb/s OQPSK mode in us. More...
 
#define THRES_ANT_DIV_DISABLE   (0x7)
 Constant THRES_ANT_DIV_DISABLED for sub-register SR_PDT_THRES in register RG_RX_CTRL. More...
 
#define THRES_ANT_DIV_ENABLE   (0x3)
 Constant THRES_ANT_DIV_ENABLE for sub-register SR_PDT_THRES in register RG_RX_CTRL. More...
 
#define TIMESTAMPING_DISABLE   (0)
 Constant TIMESTAMPING_DISABLE for sub-register SR_IRQ_2_EXT_EN in register RG_TRX_CTRL_1. More...
 
#define TIMESTAMPING_ENABLE   (1)
 Constant TIMESTAMPING_ENABLE for sub-register SR_IRQ_2_EXT_EN in register RG_TRX_CTRL_1. More...
 
#define TRANSCEIVER_NAME   "AT86RF231"
 
#define TRX_IRQ_DELAY_US   (9) /* TRX Parameter: tIRQ */
 
#define TRX_OFF_TO_PLL_ON_TIME_US   (110) /* TRX Parameter: tTR4 */
 
#define TRX_OFF_TO_SLEEP_TIME_CLKM_CYCLES   (35) /* TRX Parameter: tTR3 */
 
#define TRX_SUPPORTED_CHANNELS   (0x07FFF800)
 
#define TX_AUTO_CRC_DISABLE   (0)
 Constant TX_AUTO_CRC_ENABLE for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1. More...
 
#define TX_AUTO_CRC_ENABLE   (1)
 Constant TX_AUTO_CRC_ENABLE for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1. More...
 
#define TX_PWR_TOLERANCE   (0x80)
 Tolerance of the phyTransmitPower PIB attribute. More...
 
#define UPLD_RES_FT_DISABLE   (0)
 Constant UPLD_RES_FT_DISBALE for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1. More...
 
#define UPLD_RES_FT_ENABLE   (1)
 Constant UPLD_RES_FT_DISBALE for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1. More...
 

Typedefs

typedef enum tal_trx_status_tag tal_trx_status_t
 Transceiver states. More...
 
typedef enum trx_cmd_tag trx_cmd_t
 Transceiver commands. More...
 
typedef enum trx_irq_reason_tag trx_irq_reason_t
 Transceiver interrupt reasons. More...
 
typedef enum trx_trac_status_tag trx_trac_status_t
 Transceiver's trac status. More...
 

Enumerations

enum  tal_trx_status_tag {
  P_ON = (0),
  BUSY_RX = (1),
  BUSY_TX = (2),
  RX_ON = (6),
  TRX_OFF = (8),
  PLL_ON = (9),
  TRX_SLEEP = (15),
  BUSY_RX_AACK = (17),
  BUSY_TX_ARET = (18),
  RX_AACK_ON = (22),
  TX_ARET_ON = (25),
  RX_ON_NOCLK = (28),
  RX_AACK_ON_NOCLK = (29),
  BUSY_RX_AACK_NOCLK = (30),
  STATE_TRANSITION_IN_PROGRESS = (31),
  P_ON = (0x00),
  BUSY_RX = (0x01),
  BUSY_TX = (0x02),
  RX_ON = (0x06),
  TRX_OFF = (0x08),
  PLL_ON = (0x09),
  TRX_SLEEP = (0x0F),
  BUSY_RX_AACK = (0x11),
  BUSY_TX_ARET = (0x12),
  RX_AACK_ON = (0x16),
  TX_ARET_ON = (0x19),
  RX_ON_NOCLK = (0x1C),
  RX_AACK_ON_NOCLK = (0x1D),
  BUSY_RX_AACK_NOCLK = (0x1E),
  STATE_TRANSITION_IN_PROGRESS = (0x1F),
  P_ON = (0x00),
  BUSY_RX = (0x01),
  BUSY_TX = (0x02),
  RX_ON = (0x06),
  TRX_OFF = (0x08),
  PLL_ON = (0x09),
  TRX_SLEEP = (0x0F),
  PREP_DEEP_SLEEP = (0x10),
  BUSY_RX_AACK = (0x11),
  BUSY_TX_ARET = (0x12),
  RX_AACK_ON = (0x16),
  TX_ARET_ON = (0x19),
  STATE_TRANSITION_IN_PROGRESS = (0x1F),
  TRX_DEEP_SLEEP = (0x20),
  P_ON = (0x00),
  BUSY_RX = (0x01),
  BUSY_TX = (0x02),
  RX_ON = (0x06),
  TRX_OFF = (0x08),
  PLL_ON = (0x09),
  TRX_SLEEP = (0x0F),
  BUSY_RX_AACK = (0x11),
  BUSY_TX_ARET = (0x12),
  RX_AACK_ON = (0x16),
  TX_ARET_ON = (0x19),
  STATE_TRANSITION_IN_PROGRESS = (0x1F),
  P_ON = (0x00),
  BUSY_RX = (0x01),
  BUSY_TX = (0x02),
  RX_ON = (0x06),
  TRX_OFF = (0x08),
  PLL_ON = (0x09),
  TRX_SLEEP = (0x0F),
  BUSY_RX_AACK = (0x11),
  BUSY_TX_ARET = (0x12),
  RX_AACK_ON = (0x16),
  TX_ARET_ON = (0x19),
  RX_ON_NOCLK = (0x1C),
  RX_AACK_ON_NOCLK = (0x1D),
  BUSY_RX_AACK_NOCLK = (0x1E),
  STATE_TRANSITION_IN_PROGRESS = (0x1F)
}
 Transceiver states. More...
 
enum  trx_cmd_tag {
  CMD_NOP = (0),
  CMD_TX_START = (2),
  CMD_FORCE_TRX_OFF = (3),
  CMD_FORCE_PLL_ON = (4),
  CMD_RX_ON = (6),
  CMD_TRX_OFF = (8),
  CMD_PLL_ON = (9),
  CMD_SLEEP = (15),
  CMD_RX_AACK_ON = (22),
  CMD_TX_ARET_ON = (25),
  CMD_NOP = (0x00),
  CMD_TX_START = (0x02),
  CMD_FORCE_TRX_OFF = (0x03),
  CMD_FORCE_PLL_ON = (0x04),
  CMD_RX_ON = (0x06),
  CMD_TRX_OFF = (0x08),
  CMD_PLL_ON = (0x09),
  CMD_RX_AACK_ON = (0x16),
  CMD_TX_ARET_ON = (0x19),
  CMD_SLEEP = (0x0F),
  CMD_NOP = (0x00),
  CMD_TX_START = (0x02),
  CMD_FORCE_TRX_OFF = (0x03),
  CMD_FORCE_PLL_ON = (0x04),
  CMD_RX_ON = (0x06),
  CMD_TRX_OFF = (0x08),
  CMD_PLL_ON = (0x09),
  CMD_PREP_DEEP_SLEEP = (0x10),
  CMD_RX_AACK_ON = (0x16),
  CMD_TX_ARET_ON = (0x19),
  CMD_SLEEP = (0x0F),
  CMD_DEEP_SLEEP = (0x20),
  CMD_NOP = (0x00),
  CMD_TX_START = (0x02),
  CMD_FORCE_TRX_OFF = (0x03),
  CMD_FORCE_PLL_ON = (0x04),
  CMD_RX_ON = (0x06),
  CMD_TRX_OFF = (0x08),
  CMD_PLL_ON = (0x09),
  CMD_RX_AACK_ON = (0x16),
  CMD_TX_ARET_ON = (0x19),
  CMD_SLEEP = (0x0F),
  CMD_NOP = (0x00),
  CMD_TX_START = (0x02),
  CMD_FORCE_TRX_OFF = (0x03),
  CMD_FORCE_PLL_ON = (0x04),
  CMD_RX_ON = (0x06),
  CMD_TRX_OFF = (0x08),
  CMD_PLL_ON = (0x09),
  CMD_RX_AACK_ON = (0x16),
  CMD_TX_ARET_ON = (0x19),
  CMD_SLEEP = (0x0F)
}
 Transceiver commands. More...
 
enum  trx_irq_reason_tag {
  TRX_NO_IRQ = (0x00),
  TRX_IRQ_PLL_LOCK = (0x01),
  TRX_IRQ_PLL_UNLOCK = (0x02),
  TRX_IRQ_RX_START = (0x04),
  TRX_IRQ_TRX_END = (0x08),
  TRX_IRQ_CCA_ED_READY = (0x10),
  TRX_IRQ_AMI = (0x20),
  TRX_IRQ_TRX_UR = (0x40),
  TRX_IRQ_BAT_LOW = (0x80),
  TRX_IRQ_7_BAT_LOW = (0x80),
  TRX_IRQ_6_TRX_UR = (0x40),
  TRX_IRQ_5_AMI = (0x20),
  TRX_IRQ_4_CCA_ED_DONE = (0x10),
  TRX_IRQ_3_TRX_END = (0x08),
  TRX_IRQ_2_RX_START = (0x04),
  TRX_IRQ_1_PLL_UNLOCK = (0x02),
  TRX_IRQ_0_PLL_LOCK = (0x01),
  TRX_NO_IRQ = (0x00),
  TRX_IRQ_7_BAT_LOW = (0x80),
  TRX_IRQ_6_TRX_UR = (0x40),
  TRX_IRQ_5_AMI = (0x20),
  TRX_IRQ_4_CCA_ED_DONE = (0x10),
  TRX_IRQ_3_TRX_END = (0x08),
  TRX_IRQ_2_RX_START = (0x04),
  TRX_IRQ_1_PLL_UNLOCK = (0x02),
  TRX_IRQ_0_PLL_LOCK = (0x01),
  TRX_NO_IRQ = (0x00),
  TRX_IRQ_7_BAT_LOW = (0x80),
  TRX_IRQ_6_TRX_UR = (0x40),
  TRX_IRQ_5_AMI = (0x20),
  TRX_IRQ_4_CCA_ED_DONE = (0x10),
  TRX_IRQ_3_TRX_END = (0x08),
  TRX_IRQ_2_RX_START = (0x04),
  TRX_IRQ_1_PLL_UNLOCK = (0x02),
  TRX_IRQ_0_PLL_LOCK = (0x01),
  TRX_NO_IRQ = (0x00),
  TRX_IRQ_7_BAT_LOW = (0x80),
  TRX_IRQ_6_TRX_UR = (0x40),
  TRX_IRQ_5_AMI = (0x20),
  TRX_IRQ_4_CCA_ED_DONE = (0x10),
  TRX_IRQ_3_TRX_END = (0x08),
  TRX_IRQ_2_RX_START = (0x04),
  TRX_IRQ_1_PLL_UNLOCK = (0x02),
  TRX_IRQ_0_PLL_LOCK = (0x01),
  TRX_NO_IRQ = (0x00)
}
 Transceiver interrupt reasons. More...
 
enum  trx_trac_status_tag {
  TRAC_SUCCESS = 0,
  TRAC_SUCCESS_DATA_PENDING = 1,
  TRAC_WAIT_FOR_ACK = 2,
  TRAC_CHANNEL_ACCESS_FAILURE = 3,
  TRAC_NO_ACK = 5,
  TRAC_INVALID = 7,
  TRAC_SUCCESS = (0x00),
  TRAC_SUCCESS_DATA_PENDING = (0x01),
  TRAC_SUCCESS_WAIT_FOR_ACK = (0x02),
  TRAC_CHANNEL_ACCESS_FAILURE = (0x03),
  TRAC_NO_ACK = (0x05),
  TRAC_INVALID = (0x07),
  TRAC_SUCCESS = (0),
  TRAC_SUCCESS_DATA_PENDING = (1),
  TRAC_SUCCESS_WAIT_FOR_ACK = (2),
  TRAC_CHANNEL_ACCESS_FAILURE = (3),
  TRAC_NO_ACK = (5),
  TRAC_INVALID = (7),
  TRAC_SUCCESS = (0),
  TRAC_SUCCESS_DATA_PENDING = (1),
  TRAC_SUCCESS_WAIT_FOR_ACK = (2),
  TRAC_CHANNEL_ACCESS_FAILURE = (3),
  TRAC_NO_ACK = (5),
  TRAC_INVALID = (7),
  TRAC_SUCCESS = (0),
  TRAC_SUCCESS_DATA_PENDING = (1),
  TRAC_SUCCESS_WAIT_FOR_ACK = (2),
  TRAC_CHANNEL_ACCESS_FAILURE = (3),
  TRAC_NO_ACK = (5),
  TRAC_INVALID = (7)
}
 Transceiver's trac status. More...
 

#define AACK_ACK_TIME_12_SYMBOLS   (0)

Constants.

Constant AACK_ACK_TIME_12_symbols for sub-register SR_AACK_ACK_TIME

#define AACK_ACK_TIME_2_SYMBOLS   (1)

Constant AACK_ACK_TIME_2_symbols for sub-register SR_AACK_ACK_TIME.

#define ACK_DISABLE   (1)

Constant ACK_DISABLE for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1.

#define ACK_ENABLE   (0)

Constant ACK_ENABLE for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1.

#define AES_BASE_ADDR   (0x80)

Register addresses.

Base address for Transceiver AES address space

#define AES_DIR_DECRYPT   (1)

AES core operation direction: Decryption (ECB)

Referenced by sal_aes_setup().

#define AES_DIR_ENCRYPT   (0)

AES core operation direction: Encryption (ECB, CBC)

Referenced by compute_mic(), encrypt_pldmic(), PHY_EncryptReq(), sal_aes_setup(), and stb_ccm_secure().

#define AES_DONE   (1)

AES core operation status: AES module finished.

#define AES_MODE_CBC   (2)

Set CBC mode.

Referenced by compute_mic(), and sal_aes_setup().

#define AES_MODE_ECB   (0)
#define AES_MODE_KEY   (1)

Set key mode.

#define AES_NOT_DONE   (0)

AES core operation status: AES module did not finish.

#define AES_REQUEST   (1)

Initiate an AES operation.

#define ALTRATE_1MBPS   (2)

Constant ALTRATE_1Mbps for sub-register SR_OQPSK_DATA_RATE.

#define ALTRATE_250KBPS   (0)

Constant ALTRATE_250kbps for sub-register SR_OQPSK_DATA_RATE.

#define ALTRATE_2MBPS   (3)

Constant ALTRATE_2Mbps for sub-register SR_OQPSK_DATA_RATE.

#define ALTRATE_500KBPS   (1)

Constant ALTRATE_500kbps for sub-register SR_OQPSK_DATA_RATE.

#define ANT_CTRL_0   (0)

Constant ANT_CTRL_0 for sub-register SR_ANT_CTRL in register RG_ANT_DIV.

Referenced by config_rpc_mode(), and per_mode_initiator_rx_cb().

#define ANT_CTRL_1   (1)

Constant ANT_CTRL_1 for sub-register SR_ANT_CTRL in register RG_ANT_DIV.

Referenced by config_rpc_mode(), init_state_init(), per_mode_initiator_rx_cb(), per_mode_receptor_rx_cb(), and trx_irq_handler_cb().

#define ANT_CTRL_2   (2)

Constant ANT_CTRL_2 for sub-register SR_ANT_CTRL in register RG_ANT_DIV.

Referenced by per_mode_initiator_rx_cb(), per_mode_receptor_rx_cb(), and trx_irq_handler_cb().

#define ANT_CTRL_3   (3)

Constant ANT_CTRL_3 for sub-register SR_ANT_CTRL in register RG_ANT_DIV.

#define ANT_DIV_DISABLE   (0)

Constant ANT_DIV_disable for sub-register SR_ANT_DIV_EN.

#define ANT_DIV_ENABLE   (1)

Constant ANT_DIV_enable for sub-register SR_ANT_DIV_EN.

Referenced by trx_config().

#define ANT_EXT_SW_DISABLE   (0)

Constant ANT_EXT_SW_DISABLE for sub-register SR_ANT_EXT_SW_EN.

Referenced by set_trx_state().

#define ANT_EXT_SW_ENABLE   (1)

Constant ANT_EXT_SW_ENABLE for sub-register SR_ANT_EXT_SW_EN.

Referenced by set_trx_state(), and trx_config().

#define ANT_SEL_ANTENNA_0   (0)

Constant ANT_SEL_antenna_0 for sub-register SR_ANT_SEL.

Referenced by trx_irq_handler_cb().

#define ANT_SEL_ANTENNA_1   (1)

Constant ANT_SEL_antenna_1 for sub-register SR_ANT_SEL.

#define AT86RF231_PART_NUM   (3)

Constant RF231 for sub-register SR_PART_NUM.

Referenced by trx_init().

#define AT86RF231_VERSION_NUM   (2)

Constant RF231 for sub-register SR_VERSION_NUM.

Referenced by trx_init().

#define BATMON_ABOVE_THRES   (1)

Constant BATMON_ABOVE_THRES for sub-register SR_BATMON_OK.

Referenced by tfa_get_batmon_voltage().

#define BATMON_BELOW_THRES   (0)

Constant BATMON_BELOW_THRES for sub-register SR_BATMON_OK.

Referenced by tfa_get_batmon_voltage().

#define BATMON_HIGH_RANGE   (1)

Constant BATMON_HIGH_RANGE for sub-register BATMON_HR in register RG_BATMON.

Referenced by tfa_get_batmon_voltage().

#define BATMON_LOW_RANGE   (0)

Constant BATMON_LOW_RANGE for sub-register BATMON_HR in register RG_BATMON.

Referenced by tfa_get_batmon_voltage().

#define CCA_DETECTION_DONE   (1)

Constant CCA_calculation_done for sub-register SR_CCA_DONE.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define CCA_DETECTION_NOT_DONE   (0)

Constant CCA_calculation_not_finished for sub-register SR_CCA_DONE.

#define CCA_DETECTION_TIME_SYM   (8)
#define CCA_DURATION_SYM
Value:
#define CCA_PROCESS_TIME_SYM
Definition: avr2025_mac/source/tal/at86rf231/inc/at86rf231.h:102
#define CCA_DETECTION_TIME_SYM
Definition: avr2025_mac/source/tal/at86rf231/inc/at86rf231.h:101

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define CCA_MODE_0   (0)

Constant CCA_Mode_0 for sub-register SR_CCA_MODE.

#define CCA_MODE_1   (1)

Constant CCA_Mode_1 for sub-register SR_CCA_MODE.

#define CCA_MODE_2   (2)

Constant CCA_Mode_2 for sub-register SR_CCA_MODE.

#define CCA_MODE_3   (3)

Constant CCA_Mode_3 for sub-register SR_CCA_MODE.

#define CCA_PRE_START_DURATION_US   (20)

Referenced by perform_cca_twice().

#define CCA_PREPARATION_DURATION_US   (50)
#define CCA_PROCESS_TIME_SYM   (1)
#define CCA_START   (1)

Constant CCA_START for sub-register CCA_REQUEST in register RG_PHY_CC_CCA.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define CCA_STATUS_CHANNEL_IS_BUSY   (0)

Constant CCA_STATUS_channel_is_busy for sub-register SR_CCA_STATUS.

#define CCA_STATUS_CHANNEL_IS_IDLE   (1)

Constant CCA_STATUS_channel_is_idle for sub-register SR_CCA_STATUS.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define CLKM_16MHZ   (5)

Constant CLKM_16MHz for sub-register SR_CLKM_CTRL.

#define CLKM_1_16MHZ   (7)

Constant CLKM_1_16MHz for sub-register SR_CLKM_CTRL.

#define CLKM_1_4MHZ   (6)

Constant CLKM_1_4MHz for sub-register SR_CLKM_CTRL.

#define CLKM_1MHZ   (1)

Constant CLKM_1MHz for sub-register SR_CLKM_CTRL.

Referenced by trx_config(), and trx_init().

#define CLKM_2MHZ   (2)

Constant CLKM_2MHz for sub-register SR_CLKM_CTRL.

#define CLKM_4MHZ   (3)

Constant CLKM_4MHz for sub-register SR_CLKM_CTRL.

#define CLKM_8MHZ   (4)

Constant CLKM_8MHz for sub-register SR_CLKM_CTRL.

#define CLKM_NO_CLOCK   (0)

Constant CLKM_no_clock for sub-register SR_CLKM_CTRL.

#define CLKM_SHA_DISABLE   (0)

Constant CLKM_SHA_disable for sub-register SR_CLKM_SHA_SEL.

Referenced by trx_config().

#define CLKM_SHA_ENABLE   (1)

Constant CLKM_SHA_enable for sub-register SR_CLKM_SHA_SEL.

#define CRC16_NOT_VALID   (0)

Constant CRC16_not_valid for sub-register SR_RX_CRC_VALID.

Referenced by handle_received_frame_irq().

#define CRC16_VALID   (1)

Constant CRC16_valid for sub-register SR_RX_CRC_VALID.

#define CSMA_PROCESSING_TIME_US   (100)
#define FRAME_VERSION_0   (0)

Constant FRAME_VERSION_0 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1.

#define FRAME_VERSION_01   (1)

Constant FRAME_VERSION_01 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1.

Referenced by trx_config().

#define FRAME_VERSION_012   (2)

Constant FRAME_VERSION_012 for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1.

#define FRAME_VERSION_IGNORED   (3)

Constant FRAME_VERSION_IGNORED for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1.

#define IRQ_MASK_MODE_OFF   (0)

Constant IRQ_MASK_MODE_off for sub-register SR_IRQ_MASK_MODE.

#define IRQ_MASK_MODE_ON   (1)

Constant IRQ_MASK_MODE_on for sub-register SR_IRQ_MASK_MODE.

Referenced by trx_config().

#define IRQ_POL_HIGH_ACTIVE_IRQ   (0)

Constant IRQ_POL_high_active_IRQ for sub-register SR_IRQ_POLARITY.

#define IRQ_POL_LOW_ACTIVE_IRQ   (1)

Constant IRQ_POL_low_active_IRQ for sub-register SR_IRQ_POLARITY.

#define IRQ_PROCESSING_DLY_US   (32)

Referenced by send_frame(), and tx_done_handling().

#define OQPSK_SCRAM_DISABLE   (0)

Constant OQPSK_SCRAM_DISABLE for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2.

#define OQPSK_SCRAM_ENABLE   (1)

Constant OQPSK_SCRAM_ENABLE for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2.

#define P_ON_TO_CLKM_AVAILABLE_MAX_US
Value:
(1000) /* TRX Parameter: tTR1 max.
* value */
#define P_ON_TO_CLKM_AVAILABLE_TYP_US
Value:
(330) /* TRX Parameter: tTR1
* typical value */

Referenced by trx_init().

#define PA_BUF_LT_0_US   (0)

Constant PA_BUF_LT_0s for sub-register SR_PA_BUF_LT.

#define PA_BUF_LT_2_US   (1)

Constant PA_BUF_LT_2s for sub-register SR_PA_BUF_LT.

#define PA_BUF_LT_4_US   (2)

Constant PA_BUF_LT_4s for sub-register SR_PA_BUF_LT.

#define PA_BUF_LT_6_US   (3)

Constant PA_BUF_LT_6s for sub-register SR_PA_BUF_LT.

#define PA_EXT_DISABLE   (0)

Constant PA_EXT_disable for sub-register SR_PA_EXT_EN.

Referenced by peer_search_initiator_init(), peer_search_receptor_init(), and set_trx_state().

#define PA_EXT_ENABLE   (1)

Constant PA_EXT_enable for sub-register SR_PA_EXT_EN.

Referenced by per_mode_initiator_init(), per_mode_receptor_init(), set_trx_state(), and trx_config().

#define PA_LT_2_US   (0)

Constant PA_LT_2s for sub-register SR_PA_LT.

#define PA_LT_4_US   (1)

Constant PA_LT_4s for sub-register SR_PA_LT.

#define PA_LT_6_US   (2)

Constant PA_LT_6s for sub-register SR_PA_LT.

#define PA_LT_8_US   (3)

Constant PA_LT_8s for sub-register SR_PA_LT.

#define PAD_CLKM_2_MA   (0)

Constant PAD_CLKM_2mA for sub-register SR_PAD_IO_CLKM.

Referenced by trx_config().

#define PAD_CLKM_4_MA   (1)

Constant PAD_CLKM_4mA for sub-register SR_PAD_IO_CLKM.

#define PAD_CLKM_6_MA   (2)

Constant PAD_CLKM_6mA for sub-register SR_PAD_IO_CLKM.

#define PAD_CLKM_8_MA   (3)

Constant PAD_CLKM_8mA for sub-register SR_PAD_IO_CLKM.

#define PAD_IO_2_MA   (0)

Constant PAD_IO_2mA for sub-register SR_PAD_IO.

#define PAD_IO_4_MA   (1)

Constant PAD_IO_4mA for sub-register SR_PAD_IO.

#define PAD_IO_6_MA   (2)

Constant PAD_IO_6mA for sub-register SR_PAD_IO.

#define PAD_IO_8_MA   (3)

Constant PAD_IO_8mA for sub-register SR_PAD_IO.

#define PD_ACK_BIT_SET_DISABLE   (0)

Constant PD_ACK_BIT_SET_DISABLE for sub-register AACK_SET_PD in register RG_CSMA_SEED_1.

#define PD_ACK_BIT_SET_ENABLE   (1)

Constant PD_ACK_BIT_SET_ENABLE for sub-register AACK_SET_PD in register RG_CSMA_SEED_1.

Referenced by trx_config().

#define PRE_TX_DURATION_US   (32)
#define PROM_MODE_DISABLE   (0)

Constant PROM_MODE_DISABLE for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1.

#define PROM_MODE_ENABLE   (1)

Constant PROM_MODE_ENABLE for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1.

#define RF231_RAM_SIZE   (0x80)

RF231 FIFO size.

#define RG_AES_CTRL   (0x03)

Offset for register AES_CTRL.

#define RG_AES_CTRL_MIRROR   (0x94)

mirrored version of AES_CTRL, SRAM address

#define RG_AES_STATE_KEY_0   (0x04)

Offset for register AES_STATE_KEY_0.

#define RG_AES_STATUS   (0x02)

Offset for register AES_STATUS.

#define RG_ANT_DIV   (0x0d)

Offset for register ANT_DIV.

#define RG_BATMON   (0x11)

Offset for register BATMON.

#define RG_CCA_THRES   (0x09)

Offset for register CCA_THRES.

#define RG_CSMA_BE   (0x2f)

Offset for register CSMA_BE.

#define RG_CSMA_SEED_0   (0x2d)

Offset for register CSMA_SEED_0.

Referenced by set_trx_state(), and trx_config().

#define RG_CSMA_SEED_1   (0x2e)

Offset for register CSMA_SEED_1.

#define RG_FTN_CTRL   (0x18)

Offset for register FTN_CTRL.

#define RG_IEEE_ADDR_0   (0x24)

Offset for register IEEE_ADDR_0.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define RG_IEEE_ADDR_1   (0x25)

Offset for register IEEE_ADDR_1.

#define RG_IEEE_ADDR_2   (0x26)

Offset for register IEEE_ADDR_2.

#define RG_IEEE_ADDR_3   (0x27)

Offset for register IEEE_ADDR_3.

#define RG_IEEE_ADDR_4   (0x28)

Offset for register IEEE_ADDR_4.

#define RG_IEEE_ADDR_5   (0x29)

Offset for register IEEE_ADDR_5.

#define RG_IEEE_ADDR_6   (0x2a)

Offset for register IEEE_ADDR_6.

#define RG_IEEE_ADDR_7   (0x2b)

Offset for register IEEE_ADDR_7.

#define RG_IRQ_MASK   (0x0e)

Offset for register IRQ_MASK.

Referenced by set_trx_state(), switch_pll_on(), trx_config(), and trx_init().

#define RG_MAN_ID_0   (0x1e)

Offset for register MAN_ID_0.

#define RG_MAN_ID_1   (0x1f)

Offset for register MAN_ID_1.

#define RG_PAN_ID_0   (0x22)

Offset for register PAN_ID_0.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define RG_PAN_ID_1   (0x23)

Offset for register PAN_ID_1.

#define RG_PART_NUM   (0x1c)

Offset for register PART_NUM.

Referenced by tfa_continuous_tx_start(), and trx_init().

#define RG_PHY_CC_CCA   (0x08)

Offset for register PHY_CC_CCA.

#define RG_PHY_ED_LEVEL   (0x07)

Offset for register PHY_ED_LEVEL.

Referenced by handle_received_frame_irq(), and tfa_ed_sample().

#define RG_PHY_RSSI   (0x06)

Offset for register PHY_RSSI.

#define RG_PHY_TX_PWR   (0x05)

Offset for register PHY_TX_PWR.

Referenced by set_default_tx_pwr(), tal_pib_set(), and write_all_tal_pib_to_trx().

#define RG_PLL_CF   (0x1a)

Offset for register PLL_CF.

Referenced by switch_pll_on().

#define RG_PLL_DCU   (0x1b)

Offset for register PLL_DCU.

#define RG_RX_CTRL   (0x0a)

Offset for register RX_CTRL.

Referenced by tfa_continuous_tx_start().

#define RG_RX_SYN   (0x15)

Offset for register RX_SYN.

#define RG_SFD_VALUE   (0x0b)

Offset for register SFD_VALUE.

#define RG_SHORT_ADDR_0   (0x20)

Offset for register SHORT_ADDR_0.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define RG_SHORT_ADDR_1   (0x21)

Offset for register SHORT_ADDR_1.

#define RG_TRX_CTRL_0   (0x03)

Offset for register TRX_CTRL_0.

#define RG_TRX_CTRL_1   (0x04)

Offset for register TRX_CTRL_1.

#define RG_TRX_CTRL_2   (0x0c)

Offset for register TRX_CTRL_2.

Referenced by config_per_test_parameters(), config_rpc_mode(), and tfa_continuous_tx_start().

#define RG_TRX_STATE   (0x02)

Offset for register TRX_STATE.

Referenced by set_trx_state(), switch_pll_on(), tfa_continuous_tx_start(), and trx_init().

#define RG_TRX_STATUS   (0x01)

Offset for register TRX_STATUS.

Referenced by set_trx_state().

#define RG_VERSION_NUM   (0x1d)

Offset for register VERSION_NUM.

Referenced by trx_init().

#define RG_VREG_CTRL   (0x10)

Offset for register VREG_CTRL.

#define RG_XAH_CTRL_0   (0x2c)

Offset for register XAH_CTRL_0.

#define RG_XAH_CTRL_1   (0x17)

Offset for register XAH_CTRL_1.

#define RG_XOSC_CTRL   (0x12)

Offset for register XOSC_CTRL.

#define RSSI_BASE_VAL_DBM   (-91)

Minimum RSSI sensitivity value in dBm, which is equivalent to the value 0 in sub register SR_RSSI.

Referenced by per_mode_initiator_ed_end_cb(), tal_get_rssi_base_val(), and tfa_pib_set().

#define RST_PULSE_WIDTH_US   (10)

Referenced by trx_init(), and trx_reset().

#define RX_DISABLE   (1)

Constant RX_DISABLE for sub-register RX_PDT_DIS.

Referenced by perform_cca_twice(), tfa_cca_perform(), and tfa_ed_sample().

#define RX_ENABLE   (0)

Constant RX_ENABLE for sub-register RX_PDT_DIS.

Referenced by perform_cca_twice(), tal_generate_rand_seed(), tfa_cca_perform(), and tfa_ed_sample().

#define RX_SAFE_MODE_DISABLE   (0)

Constant RX_SAFE_MODE_DISABLE for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2.

#define RX_SAFE_MODE_ENABLE   (1)

Constant RX_SAFE_MODE_ENABLE for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2.

Referenced by trx_config().

#define SLEEP_TO_TRX_OFF_MAX_US
Value:
(1000) /* TRX Parameter: tTR2 max.
* value */
#define SLEEP_TO_TRX_OFF_TYP_US
Value:
(380) /* TRX Parameter: tTR2
* typical value */

Referenced by csma_backoff_calculation(), perform_cca_twice(), and trx_reset().

#define SPI_CMD_MODE_DEFAULT   (0)

Constant SPI_CMD_MODE_default for sub-register SR_SPI_CMD_MODE.

#define SPI_CMD_MODE_MONITOR_IRQ_STATUS   (3)

Constant SPI_CMD_MODE_monitor_IRQ_STATUS for sub-register SR_SPI_CMD_MODE.

#define SPI_CMD_MODE_MONITOR_PHY_RSSI   (2)

Constant SPI_CMD_MODE_monitor_PHY_RSSI for sub-register SR_SPI_CMD_MODE.

#define SPI_CMD_MODE_MONITOR_TRX_STATUS   (1)

Constant SPI_CMD_MODE_monitor_TRX_STATUS for sub-register SR_SPI_CMD_MODE.

#define SR_AACK_ACK_TIME   0x17, 0x04, 2

Subregister access.

Access parameters for sub-register AACK_ACK_TIME in register RG_XAH_CTRL_1

Referenced by apply_channel_page_configuration().

#define SR_AACK_DIS_ACK   0x2e, 0x10, 4

Access parameters for sub-register AACK_DIS_ACK in register RG_CSMA_SEED_1.

#define SR_AACK_FLTR_RES_FT   0x17, 0x20, 5

Access parameters for sub-register AACK_FLTR_RES_FT in register RG_XAH_CTRL_1.

#define SR_AACK_FVN_MODE   0x2e, 0xc0, 6

Access parameters for sub-register AACK_FVN_MODE in register RG_CSMA_SEED_1.

Referenced by trx_config().

#define SR_AACK_I_AM_COORD   0x2e, 0x08, 3

Access parameters for sub-register AACK_I_AM_COORD in register RG_CSMA_SEED_1.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_AACK_PROM_MODE   0x17, 0x02, 1

Access parameters for sub-register AACK_PROM_MODE in register RG_XAH_CTRL_1.

Referenced by tal_get_curr_trx_config().

#define SR_AACK_SET_PD   0x2e, 0x20, 5

Access parameters for sub-register AACK_SET_PD in register RG_CSMA_SEED_1.

Referenced by trx_config().

#define SR_AACK_UPLD_RES_FT   0x17, 0x10, 4

Access parameters for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1.

#define SR_AES_DIR   0x03, 0x08, 3

Access parameters for sub-register AES_DIR in register RG_AES_CTRL.

#define SR_AES_MODE   0x03, 0x70, 4

Access parameters for sub-register AES_MODE in register RG_AES_CTRL.

#define SR_AES_REQUEST   0x03, 0x80, 7

Access parameters for sub-register AES_REQUEST in register RG_AES_CTRL.

#define SR_ANT_CTRL   0x0d, 0x03, 0

Access parameters for sub-register ANT_CTRL in register RG_ANT_DIV.

Referenced by tal_get_curr_trx_config(), trx_config(), and trx_irq_handler_cb().

#define SR_ANT_DIV_EN   0x0d, 0x08, 3

Access parameters for sub-register ANT_DIV_EN in register RG_ANT_DIV.

Referenced by tal_get_curr_trx_config(), and trx_config().

#define SR_ANT_EXT_SW_EN   0x0d, 0x04, 2

Access parameters for sub-register ANT_EXT_SW_EN in register RG_ANT_DIV.

Referenced by set_trx_state(), and trx_config().

#define SR_ANT_SEL   0x0d, 0x80, 7

Access parameters for sub-register ANT_SEL in register RG_ANT_DIV.

Referenced by tal_get_curr_trx_config(), and trx_irq_handler_cb().

#define SR_AVDD_OK   0x10, 0x40, 6

Access parameters for sub-register AVDD_OK in register RG_VREG_CTRL.

#define SR_AVREG_EXT   0x10, 0x80, 7

Access parameters for sub-register AVREG_EXT in register RG_VREG_CTRL.

#define SR_BATMON_HR   0x11, 0x10, 4

Access parameters for sub-register BATMON_HR in register RG_BATMON.

Referenced by tfa_get_batmon_voltage().

#define SR_BATMON_OK   0x11, 0x20, 5

Access parameters for sub-register BATMON_OK in register RG_BATMON.

Referenced by tfa_get_batmon_voltage().

#define SR_BATMON_VTH   0x11, 0x0f, 0

Access parameters for sub-register BATMON_VTH in register RG_BATMON.

Referenced by tfa_get_batmon_voltage().

#define SR_CCA_DONE   0x01, 0x80, 7

Access parameters for sub-register CCA_DONE in register RG_TRX_STATUS.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define SR_CCA_ED_THRES   0x09, 0x0f, 0

Access parameters for sub-register CCA_ED_THRES in register RG_CCA_THRES.

Referenced by trx_config().

#define SR_CCA_MODE   0x08, 0x60, 5

Access parameters for sub-register CCA_MODE in register RG_PHY_CC_CCA.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_CCA_REQUEST   0x08, 0x80, 7

Access parameters for sub-register CCA_REQUEST in register RG_PHY_CC_CCA.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define SR_CCA_STATUS   0x01, 0x40, 6

Access parameters for sub-register CCA_STATUS in register RG_TRX_STATUS.

Referenced by perform_cca_twice(), and tfa_cca_perform().

#define SR_CHANNEL   0x08, 0x1f, 0

Access parameters for sub-register CHANNEL in register RG_PHY_CC_CCA.

Referenced by apply_channel_page_configuration(), tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_CLKM_CTRL   0x03, 0x07, 0

Access parameters for sub-register CLKM_CTRL in register RG_TRX_CTRL_0.

Referenced by trx_config(), and trx_init().

#define SR_CLKM_SHA_SEL   0x03, 0x08, 3

Access parameters for sub-register CLKM_SHA_SEL in register RG_TRX_CTRL_0.

Referenced by trx_config().

#define SR_CSMA_SEED_0   0x2d, 0xff, 0

Access parameters for sub-register CSMA_SEED_0 in register RG_CSMA_SEED_0.

#define SR_CSMA_SEED_1   0x2e, 0x07, 0

Access parameters for sub-register CSMA_SEED_1 in register RG_CSMA_SEED_1.

Referenced by set_trx_state(), and trx_config().

#define SR_DVDD_OK   0x10, 0x04, 2

Access parameters for sub-register DVDD_OK in register RG_VREG_CTRL.

#define SR_DVREG_EXT   0x10, 0x08, 3

Access parameters for sub-register DVREG_EXT in register RG_VREG_CTRL.

#define SR_ED_LEVEL   0x07, 0xff, 0

Access parameters for sub-register ED_LEVEL in register RG_PHY_ED_LEVEL.

#define SR_FTN_START   0x18, 0x80, 7

Access parameters for sub-register FTN_START in register RG_FTN_CTRL.

#define SR_IEEE_ADDR_0   0x24, 0xff, 0

Access parameters for sub-register IEEE_ADDR_0 in register RG_IEEE_ADDR_0.

#define SR_IEEE_ADDR_1   0x25, 0xff, 0

Access parameters for sub-register IEEE_ADDR_1 in register RG_IEEE_ADDR_1.

#define SR_IEEE_ADDR_2   0x26, 0xff, 0

Access parameters for sub-register IEEE_ADDR_2 in register RG_IEEE_ADDR_2.

#define SR_IEEE_ADDR_3   0x27, 0xff, 0

Access parameters for sub-register IEEE_ADDR_3 in register RG_IEEE_ADDR_3.

#define SR_IEEE_ADDR_4   0x28, 0xff, 0

Access parameters for sub-register IEEE_ADDR_4 in register RG_IEEE_ADDR_4.

#define SR_IEEE_ADDR_5   0x29, 0xff, 0

Access parameters for sub-register IEEE_ADDR_5 in register RG_IEEE_ADDR_5.

#define SR_IEEE_ADDR_6   0x2a, 0xff, 0

Access parameters for sub-register IEEE_ADDR_6 in register RG_IEEE_ADDR_6.

#define SR_IEEE_ADDR_7   0x2b, 0xff, 0

Access parameters for sub-register IEEE_ADDR_7 in register RG_IEEE_ADDR_7.

#define SR_IRQ_0_PLL_LOCK   0x0f, 0x01, 0

Access parameters for sub-register IRQ_0_PLL_LOCK in register RG_IRQ_STATUS.

#define SR_IRQ_1_PLL_UNLOCK   0x0f, 0x02, 1

Access parameters for sub-register IRQ_1_PLL_UNLOCK in register RG_IRQ_STATUS.

#define SR_IRQ_2_EXT_EN   0x04, 0x40, 6

Access parameters for sub-register IRQ_2_EXT_EN in register RG_TRX_CTRL_1.

Referenced by trx_config().

#define SR_IRQ_2_RX_START   0x0f, 0x04, 2

Access parameters for sub-register IRQ_2_RX_START in register RG_IRQ_STATUS.

#define SR_IRQ_3_TRX_END   0x0f, 0x08, 3

Access parameters for sub-register IRQ_3_TRX_END in register RG_IRQ_STATUS.

#define SR_IRQ_4_CCA_ED_READY   0x0f, 0x10, 4

Access parameters for sub-register IRQ_4_CCA_ED_READY in register RG_IRQ_STATUS.

#define SR_IRQ_5_AMI   0x0f, 0x20, 5

Access parameters for sub-register IRQ_5_AMI in register RG_IRQ_STATUS.

#define SR_IRQ_6_TRX_UR   0x0f, 0x40, 6

Access parameters for sub-register IRQ_6_TRX_UR in register RG_IRQ_STATUS.

#define SR_IRQ_7_BAT_LOW   0x0f, 0x80, 7

Access parameters for sub-register IRQ_7_BAT_LOW in register RG_IRQ_STATUS.

#define SR_IRQ_MASK   0x0e, 0xff, 0

Access parameters for sub-register IRQ_MASK in register RG_IRQ_MASK.

Referenced by set_trx_state().

#define SR_IRQ_MASK_MODE   0x04, 0x02, 1

Access parameters for sub-register IRQ_MASK_MODE in register RG_TRX_CTRL_1.

Referenced by trx_config().

#define SR_IRQ_POLARITY   0x04, 0x01, 0

Access parameters for sub-register IRQ_POLARITY in register RG_TRX_CTRL_1.

#define SR_MAN_ID_0   0x1e, 0xff, 0

Access parameters for sub-register MAN_ID_0 in register RG_MAN_ID_0.

#define SR_MAN_ID_1   0x1f, 0xff, 0

Access parameters for sub-register MAN_ID_1 in register RG_MAN_ID_1.

#define SR_MAX_BE   0x2f, 0xf0, 4

Access parameters for sub-register MAX_BE in register RG_CSMA_BE.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_MAX_CSMA_RETRIES   0x2c, 0x0e, 1

Access parameters for sub-register MAX_CSMA_RETRIES in register RG_XAH_CTRL_0.

Referenced by send_frame(), and write_all_tal_pib_to_trx().

#define SR_MAX_FRAME_RETRIES   0x2c, 0xf0, 4

Access parameters for sub-register MAX_FRAME_RETRIES in register RG_XAH_CTRL_0.

Referenced by send_frame(), and write_all_tal_pib_to_trx().

#define SR_MIN_BE   0x2f, 0x0f, 0

Access parameters for sub-register MIN_BE in register RG_CSMA_BE.

Referenced by tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_OQPSK_DATA_RATE   0x0c, 0x03, 0

Access parameters for sub-register OQPSK_DATA_RATE in register RG_TRX_CTRL_2.

Referenced by apply_channel_page_configuration().

#define SR_OQPSK_SCRAM_EN   0x0C, 0x20, 5

Access parameters for sub-register OQPSK_SCRAM_EN in register RG_TRX_CTRL_2.

#define SR_PA_BUF_LT   0x05, 0xc0, 6

Access parameters for sub-register PA_BUF_LT in register RG_PHY_TX_PWR.

#define SR_PA_EXT_EN   0x04, 0x80, 7

Access parameters for sub-register PA_EXT_EN in register RG_TRX_CTRL_1.

Referenced by per_mode_receptor_init(), set_trx_state(), and trx_config().

#define SR_PA_LT   0x05, 0x30, 4

Access parameters for sub-register PA_LT in register RG_PHY_TX_PWR.

#define SR_PAD_IO   0x03, 0xc0, 6

Access parameters for sub-register PAD_IO in register RG_TRX_CTRL_0.

#define SR_PAD_IO_CLKM   0x03, 0x30, 4

Access parameters for sub-register PAD_IO_CLKM in register RG_TRX_CTRL_0.

Referenced by trx_config().

#define SR_PAN_ID_0   0x22, 0xff, 0

Access parameters for sub-register PAN_ID_0 in register RG_PAN_ID_0.

#define SR_PAN_ID_1   0x23, 0xff, 0

Access parameters for sub-register PAN_ID_1 in register RG_PAN_ID_1.

#define SR_PART_NUM   0x1c, 0xff, 0

Access parameters for sub-register PART_NUM in register RG_PART_NUM.

#define SR_PDT_THRES   0x0a, 0x0f, 0

Access parameters for sub-register PDT_THRES in register RG_RX_CTRL.

Referenced by trx_config().

#define SR_PLL_CF_START   0x1a, 0x80, 7

Access parameters for sub-register PLL_CF_START in register RG_PLL_CF.

#define SR_PLL_DCU_START   0x1b, 0x80, 7

Access parameters for sub-register PLL_DCU_START in register RG_PLL_DCU.

#define SR_RND_VALUE   0x06, 0x60, 5

Access parameters for sub-register RND_VALUE in register RG_PHY_RSSI.

Referenced by tal_generate_rand_seed().

#define SR_RSSI   0x06, 0x1f, 0

Access parameters for sub-register RSSI in register RG_PHY_RSSI.

#define SR_RX_BL_CTRL   0x04, 0x10, 4

Access parameters for sub-register RX_BL_CTRL in register RG_TRX_CTRL_1.

#define SR_RX_CRC_VALID   0x06, 0x80, 7

Access parameters for sub-register RX_CRC_VALID in register RG_PHY_RSSI.

Referenced by handle_received_frame_irq().

#define SR_RX_PDT_DIS   0x15, 0x80, 7

Access parameters for sub-register RX_PDT_DIS in register RG_RX_SYN.

Referenced by perform_cca_twice(), tal_generate_rand_seed(), tfa_cca_perform(), and tfa_ed_sample().

#define SR_RX_PDT_LEVEL   0x15, 0x0f, 0

Access parameters for sub-register RX_PDT_LEVEL in register RG_RX_SYN.

Referenced by tfa_pib_set().

#define SR_RX_SAFE_MODE   0x0c, 0x80, 7

Access parameters for sub-register RX_SAFE_MODE in register RG_TRX_CTRL_2.

Referenced by trx_config().

#define SR_SFD_VALUE   0x0b, 0xff, 0

Access parameters for sub-register SFD_VALUE in register RG_SFD_VALUE.

#define SR_SHORT_ADDR_0   0x20, 0xff, 0

Access parameters for sub-register SHORT_ADDR_0 in register RG_SHORT_ADDR_0.

#define SR_SHORT_ADDR_1   0x21, 0xff, 0

Access parameters for sub-register SHORT_ADDR_1 in register RG_SHORT_ADDR_1.

#define SR_SLOTTED_OPERATION   0x2c, 0x01, 0

Access parameters for sub-register SLOTTED_OPERATION in register RG_XAH_CTRL_0.

#define SR_SPI_CMD_MODE   0x04, 0x0c, 2

Access parameters for sub-register SPI_CMD_MODE in register RG_TRX_CTRL_1.

#define SR_TRAC_STATUS   0x02, 0xe0, 5

Access parameters for sub-register TRAC_STATUS in register RG_TRX_STATE.

Referenced by handle_tx_end_irq().

#define SR_TRX_CMD   0x02, 0x1f, 0

Access parameters for sub-register TRX_CMD in register RG_TRX_STATE.

#define SR_TRX_STATUS   0x01, 0x1f, 0

Access parameters for sub-register TRX_STATUS in register RG_TRX_STATUS.

Referenced by set_trx_state(), switch_pll_on(), tal_get_trx_status(), trx_init(), and trx_reset().

#define SR_TX_AUTO_CRC_ON   0x04, 0x20, 5

Access parameters for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1.

Referenced by tfa_continuous_tx_start().

#define SR_TX_PWR   0x05, 0x0f, 0

Access parameters for sub-register TX_PWR in register RG_PHY_TX_PWR.

Referenced by tal_get_curr_trx_config(), tal_pib_set(), and write_all_tal_pib_to_trx().

#define SR_VERSION_NUM   0x1d, 0xff, 0

Access parameters for sub-register VERSION_NUM in register RG_VERSION_NUM.

#define SR_XTAL_MODE   0x12, 0xf0, 4

Access parameters for sub-register XTAL_MODE in register RG_XOSC_CTRL.

#define SR_XTAL_TRIM   0x12, 0x0f, 0

Access parameters for sub-register XTAL_TRIM in register RG_XOSC_CTRL.

#define T_OCT   32

Duration of an octet for 250kb/s OQPSK mode in us.

#define T_SYM   16

Duration of an symbol for 250kb/s OQPSK mode in us.

#define THRES_ANT_DIV_DISABLE   (0x7)

Constant THRES_ANT_DIV_DISABLED for sub-register SR_PDT_THRES in register RG_RX_CTRL.

#define THRES_ANT_DIV_ENABLE   (0x3)

Constant THRES_ANT_DIV_ENABLE for sub-register SR_PDT_THRES in register RG_RX_CTRL.

Referenced by trx_config().

#define TIMESTAMPING_DISABLE   (0)

Constant TIMESTAMPING_DISABLE for sub-register SR_IRQ_2_EXT_EN in register RG_TRX_CTRL_1.

#define TIMESTAMPING_ENABLE   (1)

Constant TIMESTAMPING_ENABLE for sub-register SR_IRQ_2_EXT_EN in register RG_TRX_CTRL_1.

Referenced by trx_config().

#define TRANSCEIVER_NAME   "AT86RF231"

Referenced by get_board_details(), and get_node_info().

#define TRX_IRQ_DELAY_US   (9) /* TRX Parameter: tIRQ */

Referenced by send_frame(), and tx_done_handling().

#define TRX_OFF_TO_PLL_ON_TIME_US   (110) /* TRX Parameter: tTR4 */

Referenced by perform_cca_twice(), and switch_pll_on().

#define TRX_OFF_TO_SLEEP_TIME_CLKM_CYCLES   (35) /* TRX Parameter: tTR3 */

Referenced by set_trx_state().

#define TRX_SUPPORTED_CHANNELS   (0x07FFF800)
#define TX_AUTO_CRC_DISABLE   (0)

Constant TX_AUTO_CRC_ENABLE for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1.

Referenced by tfa_continuous_tx_start().

#define TX_AUTO_CRC_ENABLE   (1)

Constant TX_AUTO_CRC_ENABLE for sub-register TX_AUTO_CRC_ON in register RG_TRX_CTRL_1.

#define TX_PWR_TOLERANCE   (0x80)

Tolerance of the phyTransmitPower PIB attribute.

This is encoded into the two MSBits of the attribute, and is effectively read-only.

Referenced by limit_tx_pwr(), and set_default_tx_pwr().

#define UPLD_RES_FT_DISABLE   (0)

Constant UPLD_RES_FT_DISBALE for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1.

#define UPLD_RES_FT_ENABLE   (1)

Constant UPLD_RES_FT_DISBALE for sub-register AACK_UPLD_RES_FT in register RG_XAH_CTRL_1.

Transceiver states.

typedef enum trx_cmd_tag trx_cmd_t

Transceiver commands.

Transceiver interrupt reasons.

Transceiver's trac status.

Transceiver states.

Enumerator
P_ON 

Constant P_ON for sub-register SR_TRX_STATUS.

BUSY_RX 

Constant BUSY_RX for sub-register SR_TRX_STATUS.

BUSY_TX 

Constant BUSY_TX for sub-register SR_TRX_STATUS.

RX_ON 

Constant RX_ON for sub-register SR_TRX_STATUS.

TRX_OFF 

Constant TRX_OFF for sub-register SR_TRX_STATUS.

PLL_ON 

Constant PLL_ON for sub-register SR_TRX_STATUS.

TRX_SLEEP 

Constant SLEEP for sub-register SR_TRX_STATUS.

BUSY_RX_AACK 

Constant BUSY_RX_AACK for sub-register SR_TRX_STATUS.

BUSY_TX_ARET 

Constant BUSY_TX_ARET for sub-register SR_TRX_STATUS.

RX_AACK_ON 

Constant RX_AACK_ON for sub-register SR_TRX_STATUS.

TX_ARET_ON 

Constant TX_ARET_ON for sub-register SR_TRX_STATUS.

RX_ON_NOCLK 

Constant RX_ON_NOCLK for sub-register SR_TRX_STATUS.

RX_AACK_ON_NOCLK 

Constant RX_AACK_ON_NOCLK for sub-register SR_TRX_STATUS.

BUSY_RX_AACK_NOCLK 

Constant BUSY_RX_AACK_NOCLK for sub-register SR_TRX_STATUS.

STATE_TRANSITION_IN_PROGRESS 

Constant STATE_TRANSITION_IN_PROGRESS for sub-register SR_TRX_STATUS.

P_ON 

Constant P_ON for sub-register SR_TRX_STATUS.

BUSY_RX 

Constant BUSY_RX for sub-register SR_TRX_STATUS.

BUSY_TX 

Constant BUSY_TX for sub-register SR_TRX_STATUS.

RX_ON 

Constant RX_ON for sub-register SR_TRX_STATUS.

TRX_OFF 

Constant TRX_OFF for sub-register SR_TRX_STATUS.

PLL_ON 

Constant PLL_ON for sub-register SR_TRX_STATUS.

TRX_SLEEP 

Constant TRX_SLEEP for sub-register SR_TRX_STATUS.

BUSY_RX_AACK 

Constant BUSY_RX_AACK for sub-register SR_TRX_STATUS.

BUSY_TX_ARET 

Constant BUSY_TX_ARET for sub-register SR_TRX_STATUS.

RX_AACK_ON 

Constant RX_AACK_ON for sub-register SR_TRX_STATUS.

TX_ARET_ON 

Constant TX_ARET_ON for sub-register SR_TRX_STATUS.

RX_ON_NOCLK 

Constant RX_ON_NOCLK for sub-register SR_TRX_STATUS.

RX_AACK_ON_NOCLK 

Constant RX_AACK_ON_NOCLK for sub-register SR_TRX_STATUS.

BUSY_RX_AACK_NOCLK 

Constant BUSY_RX_AACK_NOCLK for sub-register SR_TRX_STATUS.

STATE_TRANSITION_IN_PROGRESS 

Constant STATE_TRANSITION_IN_PROGRESS for sub-register SR_TRX_STATUS.

P_ON 

Constant P_ON for sub-register SR_TRX_STATUS.

BUSY_RX 

Constant BUSY_RX for sub-register SR_TRX_STATUS.

BUSY_TX 

Constant BUSY_TX for sub-register SR_TRX_STATUS.

RX_ON 

Constant RX_ON for sub-register SR_TRX_STATUS.

TRX_OFF 

Constant TRX_OFF for sub-register SR_TRX_STATUS.

PLL_ON 

Constant PLL_ON for sub-register SR_TRX_STATUS.

TRX_SLEEP 

Constant TRX_SLEEP for sub-register SR_TRX_STATUS.

PREP_DEEP_SLEEP 

Constant PREP_DEEP_SLEEP for sub-register SR_TRX_STATUS.

BUSY_RX_AACK 

Constant BUSY_RX_AACK for sub-register SR_TRX_STATUS.

BUSY_TX_ARET 

Constant BUSY_TX_ARET for sub-register SR_TRX_STATUS.

RX_AACK_ON 

Constant RX_AACK_ON for sub-register SR_TRX_STATUS.

TX_ARET_ON 

Constant TX_ARET_ON for sub-register SR_TRX_STATUS.

STATE_TRANSITION_IN_PROGRESS 

Constant STATE_TRANSITION_IN_PROGRESS for sub-register SR_TRX_STATUS.

TRX_DEEP_SLEEP 

Software implemented state.

P_ON 

Constant P_ON for sub-register SR_TRX_STATUS.

BUSY_RX 

Constant BUSY_RX for sub-register SR_TRX_STATUS.

BUSY_TX 

Constant BUSY_TX for sub-register SR_TRX_STATUS.

RX_ON 

Constant RX_ON for sub-register SR_TRX_STATUS.

TRX_OFF 

Constant TRX_OFF for sub-register SR_TRX_STATUS.

PLL_ON 

Constant PLL_ON for sub-register SR_TRX_STATUS.

TRX_SLEEP 

Constant TRX_SLEEP for sub-register SR_TRX_STATUS.

BUSY_RX_AACK 

Constant BUSY_RX_AACK for sub-register SR_TRX_STATUS.

BUSY_TX_ARET 

Constant BUSY_TX_ARET for sub-register SR_TRX_STATUS.

RX_AACK_ON 

Constant RX_AACK_ON for sub-register SR_TRX_STATUS.

TX_ARET_ON 

Constant TX_ARET_ON for sub-register SR_TRX_STATUS.

STATE_TRANSITION_IN_PROGRESS 

Constant STATE_TRANSITION_IN_PROGRESS for sub-register SR_TRX_STATUS.

P_ON 

Constant P_ON for sub-register SR_TRX_STATUS.

BUSY_RX 

Constant BUSY_RX for sub-register SR_TRX_STATUS.

BUSY_TX 

Constant BUSY_TX for sub-register SR_TRX_STATUS.

RX_ON 

Constant RX_ON for sub-register SR_TRX_STATUS.

TRX_OFF 

Constant TRX_OFF for sub-register SR_TRX_STATUS.

PLL_ON 

Constant PLL_ON for sub-register SR_TRX_STATUS.

TRX_SLEEP 

Constant TRX_SLEEP for sub-register SR_TRX_STATUS.

BUSY_RX_AACK 

Constant BUSY_RX_AACK for sub-register SR_TRX_STATUS.

BUSY_TX_ARET 

Constant BUSY_TX_ARET for sub-register SR_TRX_STATUS.

RX_AACK_ON 

Constant RX_AACK_ON for sub-register SR_TRX_STATUS.

TX_ARET_ON 

Constant TX_ARET_ON for sub-register SR_TRX_STATUS.

RX_ON_NOCLK 

Constant RX_ON_NOCLK for sub-register SR_TRX_STATUS.

RX_AACK_ON_NOCLK 

Constant RX_AACK_ON_NOCLK for sub-register SR_TRX_STATUS.

BUSY_RX_AACK_NOCLK 

Constant BUSY_RX_AACK_NOCLK for sub-register SR_TRX_STATUS.

STATE_TRANSITION_IN_PROGRESS 

Constant STATE_TRANSITION_IN_PROGRESS for sub-register SR_TRX_STATUS.

Transceiver commands.

Enumerator
CMD_NOP 

Constant CMD_NOP for sub-register SR_TRX_CMD.

CMD_TX_START 

Constant CMD_TX_START for sub-register SR_TRX_CMD.

CMD_FORCE_TRX_OFF 

Constant CMD_FORCE_TRX_OFF for sub-register SR_TRX_CMD.

CMD_FORCE_PLL_ON 

Constant CMD_FORCE_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_ON 

Constant CMD_RX_ON for sub-register SR_TRX_CMD.

CMD_TRX_OFF 

Constant CMD_TRX_OFF for sub-register SR_TRX_CMD.

CMD_PLL_ON 

Constant CMD_PLL_ON for sub-register SR_TRX_CMD.

CMD_SLEEP 

Software implemented command.

CMD_RX_AACK_ON 

Constant CMD_RX_AACK_ON for sub-register SR_TRX_CMD.

CMD_TX_ARET_ON 

Constant CMD_TX_ARET_ON for sub-register SR_TRX_CMD.

CMD_NOP 

Constant CMD_NOP for sub-register SR_TRX_CMD.

CMD_TX_START 

Constant CMD_TX_START for sub-register SR_TRX_CMD.

CMD_FORCE_TRX_OFF 

Constant CMD_FORCE_TRX_OFF for sub-register SR_TRX_CMD.

CMD_FORCE_PLL_ON 

Constant CMD_FORCE_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_ON 

Constant CMD_RX_ON for sub-register SR_TRX_CMD.

CMD_TRX_OFF 

Constant CMD_TRX_OFF for sub-register SR_TRX_CMD.

CMD_PLL_ON 

Constant CMD_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_AACK_ON 

Constant CMD_RX_AACK_ON for sub-register SR_TRX_CMD.

CMD_TX_ARET_ON 

Constant CMD_TX_ARET_ON for sub-register SR_TRX_CMD.

CMD_SLEEP 

Software implemented command.

CMD_NOP 

Constant CMD_NOP for sub-register SR_TRX_CMD.

CMD_TX_START 

Constant CMD_TX_START for sub-register SR_TRX_CMD.

CMD_FORCE_TRX_OFF 

Constant CMD_FORCE_TRX_OFF for sub-register SR_TRX_CMD.

CMD_FORCE_PLL_ON 

Constant CMD_FORCE_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_ON 

Constant CMD_RX_ON for sub-register SR_TRX_CMD.

CMD_TRX_OFF 

Constant CMD_TRX_OFF for sub-register SR_TRX_CMD.

CMD_PLL_ON 

Constant CMD_PLL_ON for sub-register SR_TRX_CMD.

CMD_PREP_DEEP_SLEEP 

Constant CMD_PREP_DEEP_SLEEP for sub-register SR_TRX_CMD.

CMD_RX_AACK_ON 

Constant CMD_RX_AACK_ON for sub-register SR_TRX_CMD.

CMD_TX_ARET_ON 

Constant CMD_TX_ARET_ON for sub-register SR_TRX_CMD.

CMD_SLEEP 

Software implemented command.

CMD_DEEP_SLEEP 

Software implemented command.

CMD_NOP 

Constant CMD_NOP for sub-register SR_TRX_CMD.

CMD_TX_START 

Constant CMD_TX_START for sub-register SR_TRX_CMD.

CMD_FORCE_TRX_OFF 

Constant CMD_FORCE_TRX_OFF for sub-register SR_TRX_CMD.

CMD_FORCE_PLL_ON 

Constant CMD_FORCE_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_ON 

Constant CMD_RX_ON for sub-register SR_TRX_CMD.

CMD_TRX_OFF 

Constant CMD_TRX_OFF for sub-register SR_TRX_CMD.

CMD_PLL_ON 

Constant CMD_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_AACK_ON 

Constant CMD_RX_AACK_ON for sub-register SR_TRX_CMD.

CMD_TX_ARET_ON 

Constant CMD_TX_ARET_ON for sub-register SR_TRX_CMD.

CMD_SLEEP 

Software implemented command.

CMD_NOP 

Constant CMD_NOP for sub-register SR_TRX_CMD.

CMD_TX_START 

Constant CMD_TX_START for sub-register SR_TRX_CMD.

CMD_FORCE_TRX_OFF 

Constant CMD_FORCE_TRX_OFF for sub-register SR_TRX_CMD.

CMD_FORCE_PLL_ON 

Constant CMD_FORCE_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_ON 

Constant CMD_RX_ON for sub-register SR_TRX_CMD.

CMD_TRX_OFF 

Constant CMD_TRX_OFF for sub-register SR_TRX_CMD.

CMD_PLL_ON 

Constant CMD_PLL_ON for sub-register SR_TRX_CMD.

CMD_RX_AACK_ON 

Constant CMD_RX_AACK_ON for sub-register SR_TRX_CMD.

CMD_TX_ARET_ON 

Constant CMD_TX_ARET_ON for sub-register SR_TRX_CMD.

CMD_SLEEP 

Software implemented command.

Transceiver interrupt reasons.

Enumerator
TRX_NO_IRQ 

No interrupt is indicated by IRQ_STATUS register.

TRX_IRQ_PLL_LOCK 

PLL goes to lock-state.

TRX_IRQ_PLL_UNLOCK 

Signals an unlocked PLL.

TRX_IRQ_RX_START 

Signals begin of a receiving frame.

TRX_IRQ_TRX_END 

Signals end of frames (transmit and receive)

TRX_IRQ_CCA_ED_READY 

Multi-functional interrupt: AWAKE_END: Indicates that the radio transceiver reached TRX_OFF state after P_ON, RESET, or SLEEP states.

CCA_ED_READY: Signals the end of a CCA or ED measurement.

TRX_IRQ_AMI 

Signals an address match.

TRX_IRQ_TRX_UR 

Signals a FIFO underrun.

TRX_IRQ_BAT_LOW 

Signals low battery.

TRX_IRQ_7_BAT_LOW 

Constant TRX_IRQ_7_BAT_LOW for sub-register SR_IRQ_7_BAT_LOW.

TRX_IRQ_6_TRX_UR 

Constant TRX_IRQ_6_TRX_UR for sub-register SR_IRQ_6_TRX_UR.

TRX_IRQ_5_AMI 

Constant TRX_IRQ_5_AMI for sub-register SR_IRQ_5_AMI.

TRX_IRQ_4_CCA_ED_DONE 

Constant TRX_IRQ_4_CCA_ED_DONE for sub-register SR_IRQ_4_CCA_ED_DONE.

TRX_IRQ_3_TRX_END 

Constant TRX_IRQ_3_TRX_END for sub-register SR_IRQ_3_TRX_END.

TRX_IRQ_2_RX_START 

Constant TRX_IRQ_2_RX_START for sub-register SR_IRQ_2_RX_START.

TRX_IRQ_1_PLL_UNLOCK 

Constant TRX_IRQ_1_PLL_UNLOCK for sub-register SR_IRQ_1_PLL_UNLOCK.

TRX_IRQ_0_PLL_LOCK 

Constant TRX_IRQ_0_PLL_LOCK for sub-register SR_IRQ_0_PLL_LOCK.

TRX_NO_IRQ 

No interrupt is indicated by IRQ_STATUS register.

TRX_IRQ_7_BAT_LOW 

Constant TRX_IRQ_7_BAT_LOW for sub-register SR_IRQ_7_BAT_LOW.

TRX_IRQ_6_TRX_UR 

Constant TRX_IRQ_6_TRX_UR for sub-register SR_IRQ_6_TRX_UR.

TRX_IRQ_5_AMI 

Constant TRX_IRQ_5_AMI for sub-register SR_IRQ_5_AMI.

TRX_IRQ_4_CCA_ED_DONE 

Constant TRX_IRQ_4_CCA_ED_DONE for sub-register SR_IRQ_4_CCA_ED_DONE.

TRX_IRQ_3_TRX_END 

Constant TRX_IRQ_3_TRX_END for sub-register SR_IRQ_3_TRX_END.

TRX_IRQ_2_RX_START 

Constant TRX_IRQ_2_RX_START for sub-register SR_IRQ_2_RX_START.

TRX_IRQ_1_PLL_UNLOCK 

Constant TRX_IRQ_1_PLL_UNLOCK for sub-register SR_IRQ_1_PLL_UNLOCK.

TRX_IRQ_0_PLL_LOCK 

Constant TRX_IRQ_0_PLL_LOCK for sub-register SR_IRQ_0_PLL_LOCK.

TRX_NO_IRQ 

No interrupt is indicated by IRQ_STATUS register.

TRX_IRQ_7_BAT_LOW 

Constant TRX_IRQ_7_BAT_LOW for sub-register SR_IRQ_7_BAT_LOW.

TRX_IRQ_6_TRX_UR 

Constant TRX_IRQ_6_TRX_UR for sub-register SR_IRQ_6_TRX_UR.

TRX_IRQ_5_AMI 

Constant TRX_IRQ_5_AMI for sub-register SR_IRQ_5_AMI.

TRX_IRQ_4_CCA_ED_DONE 

Constant TRX_IRQ_4_CCA_ED_DONE for sub-register SR_IRQ_4_CCA_ED_DONE.

TRX_IRQ_3_TRX_END 

Constant TRX_IRQ_3_TRX_END for sub-register SR_IRQ_3_TRX_END.

TRX_IRQ_2_RX_START 

Constant TRX_IRQ_2_RX_START for sub-register SR_IRQ_2_RX_START.

TRX_IRQ_1_PLL_UNLOCK 

Constant TRX_IRQ_1_PLL_UNLOCK for sub-register SR_IRQ_1_PLL_UNLOCK.

TRX_IRQ_0_PLL_LOCK 

Constant TRX_IRQ_0_PLL_LOCK for sub-register SR_IRQ_0_PLL_LOCK.

TRX_NO_IRQ 

No interrupt is indicated by IRQ_STATUS register.

TRX_IRQ_7_BAT_LOW 

Constant TRX_IRQ_7_BAT_LOW for sub-register SR_IRQ_7_BAT_LOW.

TRX_IRQ_6_TRX_UR 

Constant TRX_IRQ_6_TRX_UR for sub-register SR_IRQ_6_TRX_UR.

TRX_IRQ_5_AMI 

Constant TRX_IRQ_5_AMI for sub-register SR_IRQ_5_AMI.

TRX_IRQ_4_CCA_ED_DONE 

Constant TRX_IRQ_4_CCA_ED_DONE for sub-register SR_IRQ_4_CCA_ED_DONE.

TRX_IRQ_3_TRX_END 

Constant TRX_IRQ_3_TRX_END for sub-register SR_IRQ_3_TRX_END.

TRX_IRQ_2_RX_START 

Constant TRX_IRQ_2_RX_START for sub-register SR_IRQ_2_RX_START.

TRX_IRQ_1_PLL_UNLOCK 

Constant TRX_IRQ_1_PLL_UNLOCK for sub-register SR_IRQ_1_PLL_UNLOCK.

TRX_IRQ_0_PLL_LOCK 

Constant TRX_IRQ_0_PLL_LOCK for sub-register SR_IRQ_0_PLL_LOCK.

TRX_NO_IRQ 

No interrupt is indicated by IRQ_STATUS register.

Transceiver's trac status.

Enumerator
TRAC_SUCCESS 
TRAC_SUCCESS_DATA_PENDING 
TRAC_WAIT_FOR_ACK 
TRAC_CHANNEL_ACCESS_FAILURE 
TRAC_NO_ACK 
TRAC_INVALID 
TRAC_SUCCESS 

Constant TRAC_SUCCESS for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_DATA_PENDING 

Constant TRAC_SUCCESS_DATA_PENDING for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_WAIT_FOR_ACK 

Constant TRAC_SUCCESS_WAIT_FOR_ACK for sub-register SR_TRAC_STATUS.

TRAC_CHANNEL_ACCESS_FAILURE 

Constant TRAC_CHANNEL_ACCESS_FAILURE for sub-register SR_TRAC_STATUS.

TRAC_NO_ACK 

Constant TRAC_NO_ACK for sub-register SR_TRAC_STATUS.

TRAC_INVALID 

Constant TRAC_INVALID for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS 

Constant TRAC_SUCCESS for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_DATA_PENDING 

Constant TRAC_SUCCESS_DATA_PENDING for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_WAIT_FOR_ACK 

Constant TRAC_SUCCESS_WAIT_FOR_ACK for sub-register SR_TRAC_STATUS.

TRAC_CHANNEL_ACCESS_FAILURE 

Constant TRAC_CHANNEL_ACCESS_FAILURE for sub-register SR_TRAC_STATUS.

TRAC_NO_ACK 

Constant TRAC_NO_ACK for sub-register SR_TRAC_STATUS.

TRAC_INVALID 

Constant TRAC_INVALID for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS 

Constant TRAC_SUCCESS for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_DATA_PENDING 

Constant TRAC_SUCCESS_DATA_PENDING for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_WAIT_FOR_ACK 

Constant TRAC_SUCCESS_WAIT_FOR_ACK for sub-register SR_TRAC_STATUS.

TRAC_CHANNEL_ACCESS_FAILURE 

Constant TRAC_CHANNEL_ACCESS_FAILURE for sub-register SR_TRAC_STATUS.

TRAC_NO_ACK 

Constant TRAC_NO_ACK for sub-register SR_TRAC_STATUS.

TRAC_INVALID 

Constant TRAC_INVALID for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS 

Constant TRAC_SUCCESS for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_DATA_PENDING 

Constant TRAC_SUCCESS_DATA_PENDING for sub-register SR_TRAC_STATUS.

TRAC_SUCCESS_WAIT_FOR_ACK 

Constant TRAC_SUCCESS_WAIT_FOR_ACK for sub-register SR_TRAC_STATUS.

TRAC_CHANNEL_ACCESS_FAILURE 

Constant TRAC_CHANNEL_ACCESS_FAILURE for sub-register SR_TRAC_STATUS.

TRAC_NO_ACK 

Constant TRAC_NO_ACK for sub-register SR_TRAC_STATUS.

TRAC_INVALID 

Constant TRAC_INVALID for sub-register SR_TRAC_STATUS.